Shopping Cart

Your cart is empty.

Your cart is empty.

3PCS PCM5102 Stereo Lossless Digital to Analog Converter Decoder Board Voice Module I2S Interface Player Board PHAT Format with 3.5mm Jack for Arduino

5.0 Write Review
Free shipping on orders over $29.99

$12.73

$ 6 .99 $6.99

In Stock

1.NumberofItems:1


  • 【Parameters】Power supply voltage: DC 5V; Type: I2S Digital to Analog Converter decoder; Model: PCM5102; Size: 32mm x 17mm
  • 【Device Description】This PCM5102 device is a monolithic CMOS integrated circuit family that includes a stereo digital-to-analog converter and additional support circuitry in a thin small outline (TSSOP) package. The PCM5102 uses the latest generation of TI's advanced segmented DAC architecture to achieve excellent dynamic performance and improve tolerance to clock jitter.
  • 【Simple Design, High Sampling Rate】The PCM5102 provides a 2.1VRMS ground-center output, allowing designers to remove DC-blocking capacitors on the output and external squelch circuits associated with single-supply line drivers. The PCM5102 accepts industry-standard audio data formats with 16 to 32-bit data. Supports sampling rates up to 384kHz.
  • 【Super Performance】The integrated line driver outperforms all other charge pump-based line drivers by supporting loads as low as 1kΩ. By supporting loads as low as 1kΩ, the PCM5102 can actually drive up to 10 parallel products such as LCD TVs, DVDRs, AV receivers and other devices.
  • 【Reduced EMI and Distortion】The PCM5102 provides up to 20dB lower out-of-band noise than existing DAC technology, reducing EMI and distortion in downstream amplifiers/ADCs. (Measured from the traditional 100kHz octave band of noise (OBN) that has been used to 3MHz).


Features:
Market-leading low out-of-band noise
Selectable digital filter delay and performance
No capacitors required to block DC current
Integrated negative charge pump
Internal no-pop control for sample rate changes or clock stop
Intelligent squelch system: soft rising or falling ramp and analog squelch for 120dB squelch signal-to-noise ratio (SNR) with no-pop operation
Integrated high-performance audio phase-locked loop (PLL) with BCK reference to internally generated SCK
Parameter:
Model: PCM5102
Type:I2S Digital to Analog Converter Decoder
Since it's digital audio, it sounds really good, much better than the onboard analog audio. The stereo jack comes soldered onto the board already.
Line out stereo jack
PHAT format board
Uses the PCM5102A Digital to Analog Converter to work with the Raspberry Pi I2S interface
Size: 32x17mm
Dynamic Range: 112dB
SNR:112dB
THD:-93dB
Full-scale output: 2.1VRMS (centered on GND)
Normal 8x oversampling digital filter delay: 20/fS
Low latency 8x oversampling digital filter delay: 3.5/fS
Sampling frequency: 8kHz to 384kHz
System clock multiplier (fSCK): 64, 128, 192, 256, 384, 512,768,1024,1152,1536,2048, 3072; up to 50MHz.
Accepts 16, 24, and 32-bit audio data
PCM data format: I2S, left justified
When LRCK and BCK Automatically enters power saving mode when deasserted
3.3V fail-safe low voltage CMOS (LVCMOS) digital input
Hardware configuration
Single supply operation:- 3.3V analog, 3.3V digital
Integrated power-on reset
How to solve the noise problem:
optional digital filter delay and performance, No need to isolate the DC current capacitor.If there is noise when GND and SCK are connected, this problem can be solved.
Application
A/V receivers
DVD, BD players
HDTV receivers
Applications requiring 2VRMS audio output
Package contain
3PCS PCM5102 DAC Decoder