Your cart is empty.
Your cart is empty.Product Description
solid rod
Higher strength: enhanced resistance to bending, compression, and tension, allowing it to better withstand external loads and provide stable support.
5mm thickness
Enhanced support: The 5mm thick backplate ensures stronger stability, handling larger weights or pressures without bending or deformation.
1.5 inch dia.
Enhanced load-bearing: The 1.5-inch backplate distributes load, increasing capacity and preventing deformation from concentrated pressure.
rounded corner design
The floating shelf bracket rods feature a rounded corner design, which reduces snagging during assembly and ensures a smoother installation process.
Ryan B.
Reviewed in the United States on May 7, 2025
The drill bit guides are helpful. Make sure your shelf thickness is at least 1/2” larger than the width of the included spade bit or there will be tear out on the edges of the shelf. A forstner bit would work much better. Also be careful with the long spiral drill bit. It wants to suck down into the wood quickly, potentially going all the way through the shelf.
Charlene F
Reviewed in the United States on May 3, 2025
Quality product. Use double sided tape on the pegs to locate the exact mounting point on the wall. I wouldn’t trust putting much weight on these if they aren’t anchored to studs - the enclosed drywall anchors are nice for lighter tasks.
Larry Bell
Reviewed in the United States on May 27, 2025
It is very easy to install, with complete accessories and clear instructions. I used it to fix the wooden shelves in the living room. It has good load-bearing capacity and is stable without shaking. Since the installation, the storage at home has become more organized. I highly recommend it!
ER Wiksten
Reviewed in the United States on February 18, 2025
This 4-piece floating shelf bracket set is exactly what I needed for (2) 24-inch floating shelves. I didn't want unsightly brackets, and I have a 3-inch-thick slab of walnut wood I wanted to use. Everything one needs is included in this kit, along with simple tools most households have already (drill, measuring tape, level, and stud finder). This kit includes:Shelf BracketsLong Auger Bit1 5/8s Spade BitDrilling JigRouting JigAnd assorted screws, wall anchors for both drywall and concreteThere is some skill and a steady hand is needed for this project, but the results are well worth it. With this hardware, you can make custom shelves out of any type of wood that is a minimum of 2 1/2 thick. Since these brackets penetrate into the wood 4 inches, and are tied directly into the wall studs, brick, or concrete, the shelving will be incredibly strong, holding up to 160 pounds per pair. Ideal for shelving and mantles.One really nice feature is that these brackets feature an elliptical anchor design, so you have a bit of leeway in your measuring. The sleek black finish keeps these rust proof. Since I will be using 24-inch shelves, I will center the brackets 4 inches from each end, keeping in mind wall studs should be 16 inches apart. These brackets are solid, not hollow, for maximum strength. I am very pleased with this purchase.
Hayherder
Reviewed in the United States on January 27, 2025
I looked at a lot of these brackets to try and find the right one for my daughter's "floating" shelves. I bought the 8" variety for 10.5" deep shelves. Looks like I'm the first reviewer that isn't a free vine customer (i.e. - first real review). TLDR: while more expensive than similar items, I found it worth it due to precise machining, 1.5" tall drill guide, included 8" auger bit, and especially b/c two screws dead center in the stud (with L/R maneuverability).What I liked:-- 2 screws, dead-center on the wall stud. Many of the options had all 4 holes on the edges of the bracket. With this being 1.5" diameter, and the wall studs being 1.5" on edge, you would not have good hold putting 4 screws on the very edge of the wall studs. But 2 dead center? Perfect. There are 2 other holes in these, but I did not use for the same reason. You'll notice the 2 at top and bottom allow for slide left and right. This can be VERY helpful when getting several brackets lined up to go in the back of the wood 8" deep.-- As seen in my first picture, the brackets all line up; the accuracy of each is square and similar. this is key when stuffing multiples in to the wood-- the set comes with a good system to drill straight holes. In the 4th pic, you can see the drill guide which is placed inside the guide for boring out 1.5" of wood to hide the brackets. I used the rectangular piece just to line up the center of the board (marked the center with pencil first), then put 2 screws in either side to hold it. Then put the drill guide (about 1.5" tall) in the middle and screw it down as well (recommend drilling out the holes first).-- Also supplied is an 8" auger. It didn't fit my 3/8" dewalt corded drill, but it did fit my ryobi drill. Auger worked great. After drilling out the 8" holes (you can go deeper, but it does have a mark for exactly 8"), then remove the drill guide.What I didn't like:-- supplied is a 1.5" spade bit to bore out the wood so the brackets are recessed in the back, instead of the wood resting on them in the back by the wall. I guess you leave the rectangular metal piece on the wood, and then use the spade bit to bore out the wood. However, that doesn't work b/c the fit is too tight and you can't keep them from hitting one another (which almost caused some good injury to me). So, I used it to just draw the circle, and then I used a router to trim out what I needed to. You might be able to mark the circle and use the supplied space bit.-- Price. This is more expensive than many other similar options.
Frequent shopper
Reviewed in the United States on April 29, 2025
These were perfect for some custom floating shelves in my bar area. They are sturdy and hold all the heavy bottles without sagging or tilting forward. We intentionally made the shelves the shallowest they could be front to back with the length support we bought, to ensure the most support of the shelf. All of the hardware, bits and guides are included in the kit, so you just need a drill. It took the first 2 holes on the shelf to figure out the best installation order of drilling. The supports are completely hidden by the shelf and are nice as you can install them spaced to be in studs and avoid using wall anchors.
Deborah Kendrick
Reviewed in the United States on April 26, 2025
These are awesome. Easy to install. Hold a lot of weight. Highly recommend!
J. Griffin
Reviewed in the United States on April 16, 2025
Very solid. High quality. Good instructions. All the extra things you need : screws , anchors , drill bits AND templates.Would highly recommend. They are a great value.
Recommended Products