Your cart is empty.
Your cart is empty.CURT 13417 Class 3 Trailer Hitch, 2-Inch Receiver, Fits Select Ford Ranger
John Kloock
Reviewed in the United States on March 26, 2025
The hitch was a perfect fit and did not take very long at all to install. I definitely recommend this product to anybody who is looking for good quality hitch
Steven Meyer
Reviewed in the United States on February 27, 2025
Easy to install.
Aolson
Reviewed in the United States on January 28, 2025
Fits a Ranger with Tremor, with the factory recovery hooks, perfectly. Install took 10 minutes, two c-clamps and a floor jack.
Great grandma
Reviewed in the United States on April 2, 2025
It was a perfect fit for 2019 Ford Ranger. All hardware was included.
Gina
Reviewed in Canada on September 22, 2024
Très bonne livraison, le livreur assez gentil pour rentrer l’article dans la maison avec un charmant sourire.très apprécié. Fait super bien sur un Ford ranger2019. Livraison avant la date défini par le vendeur. Je vous souhaite une superbe journée.
Woody
Reviewed in the United States on February 3, 2024
Installed on my 2021 Ford Ranger Super Cab in less than 20 minutes & fit perfectly with NO issues at all. After clamping each side with a pair of vise grips I did have my friend assist by him holding one side of hitch under the truck while I held the other side & we both started the bolts by hand & I tightened all four with the 21mm socket & half inch drive ratchet & breaker bar. Very pleased with overall mission!!
Mr. Mark Hancock
Reviewed in the United States on February 2, 2024
Fitted 2019 Ford Ranger perfectly and easy to install. 4 stars because the packaging was terrible. Put in too big a box with no support. When it arrived the box was all torn up.
David English Sr
Reviewed in the United States on October 11, 2024
Easy to install and perfect for towing!
Curt McCool
Reviewed in Canada on June 13, 2023
Easy install
Mark
Reviewed in Canada on May 10, 2023
Iam very pleased with this Curt trailer hitch this is the 2nd one i have installed myself on my truck. You can literaly have this trailer hitch mounted in less than 20 minutes.Yes will fit the 2023 U.S. MODEL Ford Ranger with the TREMOR package jus have to lower the spare tire a bit to put the hicth up in position, then i pushed the spare tire up tight against the hitch and torqued the 4 bolts down.looks perfect clean fit.I would recommened this product.Tank you!
Pablo cambay
Reviewed in Canada on May 17, 2021
Fits well on my ranger 2019
Liliane M.
Reviewed in Canada on November 11, 2020
I especially like the safety of the table and chairs. A 2 yrs old can sit on the chairs without tipping the chair and falling down.
John Luiten
Reviewed in the United States on August 7, 2019
Solid product. Heavy build. Will handle whatever the truck can handle. Install is a bit more than indicated. Just finished install by myself. Can do without lifting truck. Not sure even if a lift or a second pair of hands will be helpful. Here’s what to look for. First, the instructions are not helpful—but not incorrect. They are just not quite complete. There are 4 bolts to remove and then slip the hitch in place and replace the 4 bolts. Easy, peasy—but the damn hitch is 40 pounds! Also, the 4 bolts hold the rear bumper and light tow system onto the truck. Remove those 4 bolts and the rear bumper falls off! Second the spare tire is under the truck, right behind the bumper. That tire gets in the way of the trailer hitch. Indeed, the tire was mounted too close to the rear to provide space to allow the hitch to fit.OK, how to work around this. First, drop the spare tire as if you were repairing a flat and remove it to someplace out of the way. Second, get some hand clamps and use them to hold the rear bumper in place when the 4 bolts are removed. Don’t worry about just where and how, you can loosen the two bolts on one side and see the bumper start moving. Place clamps accordingly on both sides and remove the 4bolts. Careful wrt being under the rear bumper in case the clamps slip. Third, find a foot stool of 12 to 16 inches high. Place it under the rear bumper, centered, place the hitch on top in the correct orientation, side it all under the rear end. You’ll have the hitch holes immediately under the frame holes for the 4 bolts. If there is a bit too much of a gap for the bolt, you can use one hand to push up the hitch on one side to the bolt holes and catch the two bolts to tighten slightly—which will hold the hitch, then repeat on the other side. Now the hitch is level, bolts straight (not cross threaded), but obviously loose. Tighten both sides, careful to sense for cross threading.I did not use a torque wrench. The call was for something like 200 foot pounds—I need a gauge for that? Remove clamps and reinstall tire. The tire will naturally squeeze against the new hitch and tighten against its rubber bushing pad. You do need a 25mm socket and a longish wrench or wrench with breaker bar.
Recommended Products
