Muy buena compra, funcionan excelente

does exactly what it should with a factory fit and finish. Doesn't look cheap at all. Actually higher quality than OEM!

2013 Focus ST. These things fit great and are super easy to install. There is a guy on YT who purchased these and has a install tutorial. They look super good and give a very subtle but sleek and updated look. I highly recommend. 10/10.

The media could not be loaded.

I stumbled across a YouTube review of these side mirror lights when I was looking for new headlights for Little Rojo (my focus). Personally, I don't like smoked anything BUT these would be the exception. They are sequential which is an upgrade, they're bright even though the plastic is smoked/black, and they're easy to install. Best part is, it's a 'cheap' mod to make your car look a lot better.Like I said, I watched a video on them. I'd like to make my own recommendations:1. Take a picture of where your mirrors are before you start the installation. Do this because you have to move the mirrors all the way in towards the car so you can access the snap release areas.2. Have a thin/strong flat head screwdriver. It needs to be small to access the plastic snap release and help with removing the factory light.3. Have a small high powered flash light to help you see these snap releases - there are two (2) and even in broad daylight in AZ, they were hard to see.4. The mirror housing was tight and a bit hard to remove, just keep wiggling and pulling and you'll get it off.5. A Clorox or a tough wipe of some sort would be beneficial to clean the inside once you have the mirror housing off. Again, I'm in AZ so it was dusty on the inside.6. The factory light connects at the far edge of the mirror and has a tab that holds it in place. I broke the driver side tab, which is okay they were getting replaced anyways. BUT, if you don't want to break that tab, the small flat head screwdriver will come in handy here. Start pulling from the far edge where the light is and once you wiggle it a bit, you'll see the tab. Once you start to see the tab, use the flat head to help you. (I used this method on the passenger side and didn't break that tab.)7. BUY 3M Super Strength Molding Tape (03609, 1/2 in x 5 ft). It was like 5 or 6 dollars and will give you peace of mind. The new smoked signal lights clip in easy but there were some reviews that mentioned they were a little loose. You'll see the only spot to put the tape once you have the factory light out and you'll use like 2" per side.8. The factory light was easy to remove and the smoked connector is a little tough to get in. Give it some muscle and you'll be fine.9. ***CHECK THAT YOUR LIGHTS ARE WORKING BEFORE FINISHING INSTALLATION!!!*** (Mine worked great but it would suck to have a dud and have to repeat the removal and installation process.)10. Place the smoked lights in far edge first where the tab is located. Or I guess another way to say this would be outside to inside. You'll hear a click when it's in place.11. Get the mirror housing back on. My fiancé did this part - I think he worked from the inside (closest to the car) to the outside. Again, you'll hear a click when it's in place.12. Smile, you're all done. :) (Don't forget to adjust your mirrors back to where they were before.)

Easy to install after watching a YouTube video, looks nicer than the OEM indicators.

Well packaged, arrived quickly, exactly as described. Installed easily (after watching a YouTube video on how to remove mirror cap), fitment could be a little tighter but overall pleased with the look.

I purchased these sequential turn signals for my Focus ST. I installed them and found out that one had a short in it. I had power to the connection but it would only work now and then. I contacted the seller and he got right back to me. Told him the problem and he immediately sent me a new set. I appreciate a person who backs their products and I will be buying from this seller again. Thanks so much.

I had to find a good video on YouTube to guide me through the installation, but it wasn't too bad. The fit was a little loose, so like some others I used a small piece of 3m vhb double sided tape to secure it better. I like the blacked out look, and the fulll led strip lighting up, but the directional movement doesn't really appeal to me. I don't mind having it, but could honestly live without it.

This was the best purchase for the car. These turn signals should of been on the car from the factory.

Seems good, one side fits snug other is a little loose but nothing to be worried about. looks great, cheap on price but built well, keeps out water and are bright.

The media could not be loaded.