Shopping Cart

Your cart is empty.

Your cart is empty.

Fan 50 Plus PINS Universal Ignitor Control Circuit Board Replacement for 12 VDC Furnaces（ with Fan Control）

5.0 Write Review
Free shipping on orders over $29.99

$31.00

$ 16 .99 $16.99

In Stock
  • [OEM Part Number]:232613, 232614, 31501 Kit with 33488, 33488 (included in 31501 Kit)& a 6 pin header connector, 33550L, 36716, 37875, 520741, 520814, 520871, 520820 Kit with 232613, 521099, AP4896608； UIB L POST, UIB L, UIB S, UIB 24VAC, UIB S; 05-299000-153, 05-299004-153, 05-309014-153, 10-12-15-7-7-E002, 10-12-2-12-12-E310, 10DM-12-1-12-12-E3002, 10N-12-1-5.5-5.5-E222.
  • [Fitment 1 ]:7912-II, 7916-II, 7920-II, 8012-II, FA 79D, HF 80D, DC82 25-32, DC82 35-41, FA 76D, FA 78 25-32, FA 72D, 8500-IV Series, 8500-III Series, 85-II Series, 85-I Series, 8900-I DC Series, 8900-II DC Series, 8900-III DC Series, AFSD12, AFSD16, AFMD20, AFSD20, AFMD25, AFMD30, AFMD35, DFMD30111,DFMD20111,DFMD25111,DFMD35111,DFSD12111, DFSD16111, DFSD20111.
  • [Fitment 2 ]:SF20/25/30/35/42, SF20F/25F/30F/35F/42F use 520832 wire kit, NT24/30/34SP, NT40 use 520839 wire kit, NT12/16/20S, NT12/16/20SE use 520840 wire kit, DD17DSI with date comes below 9124 use 520612, DD17DSI with date comes above 9124 use 520741. SW4D, SW6D, SW6DE, SW6DEL, SW6DEM, SW6DM, SW10D, SW10DE, SW10DEL, SW10DEM, SW10DM, SW12D, SW12DE, SW12DEL, SW16DEM, SW16DEL, SW16DEM and other vehicles.
  • [Attention]: There is a "detachable" MODE SELECT jumper and a separate set of red and orange wires on the board for converting the "old furnace" to have fan control function. (The 'Fan control function' must be used)
  • [Function]: The product can be used to upgrade old furnaces to add fan control functionality. This product can be used with standard 6-pin "edge connectors" or newer 6-pin "head" connectors to maintain backward compatibility.


Design:

The fan control ignition board is designed to turn off the fan motor if the board fails to detect flames after the third ignition attempt. Therefore, it reduces battery consumption and eliminates unnecessary cold air blowing. The fan 50 Plus pin will wait for 1 hour after turning off the fan motor and repeat the entire sequence again before permanently turning off.


Fitment:

12 VDC Furnaces


Detailed parameters:

Size: 3.35" x 4.25"

Voltage：12 VDC Operation

Flame Failure Response Time:0.8 seconds maximum

Tries for lgnition: Three

Operating Temperature: -40 to + 176°F(-40℃ to +80℃)


Attention:

The 'Fan Control' function must be used to operate this product correctly. The product is not suitable for DuoTherm 900 series furnaces with thermostats in grounding circuits.


Package Include:

1*FAN 50 PLUS Ignitor Board

1*Red wires

1*Orange wires



Recommended Products
LB-101263A - Lennox OEM Replacement Furnace Control Board

$127.00

$ 54 .99 $54.99

4.3
Select Option
CEPL130934-02 - Carrier OEM Replacement Furnace Control Board

$314.99

$ 99 .00 $99.00

5.0
Select Option
59K21 - Lennox OEM Replacement Furnace Control Circuit Board

$312.99

$ 99 .00 $99.00

4.8
Select Option
1028-928 - Rheem OEM Replacement Furnace Control Board

$195.95

$ 93 .99 $93.99

4.6
Select Option
Honeywell Furnace Fan Control Circuit Board, 8 Inches, Compatible with HVAC System

$138.59

$ 65 .99 $65.99

4.5
Select Option
50X57-290-01 - OEM Upgraded Furnace Control Board Replaces White Rodgers

$136.95

$ 60 .99 $60.99

4.6
Select Option
Trane Furnace Control Circuit Board Fits 50A67-476-01, 50A67-476, 031-01264-002, S1-03101264002

$199.68

$ 90 .99 $90.99

5.0
Select Option
PCBBF166 - OEM Upgraded Furnace Control Circuit Board Replaces Goodman

$99.49

$ 39 .99 $39.99

4.4
Select Option