Your cart is empty.
Your cart is empty.Product Description
10pcs Microwave Waveguide Cover, Microwave Oven Parts Mica Plates Sheets Microwave Oven Repairing Part for Universal Microwave Oven, Cut to Size.
Why Choose Our Microwave Waveguide Cover
-->Your original mica sheet will be burnt when food that splatters the inside of the microwave and left on that paper.
-->When the microwave oven parts in the microwave oven cannot be cleaned due to serious pollution or the black spot that has been broken down must be replaced in time, otherwise it is prone to fire and ablation, which will damage the magnetron over time.
-->The mica plates sheets are replacement sheets to use when your microwave oven is 'arcing' around or out of the chamber where the magnetron is located (small square hole inside the wall of of your microwave oven, a small piece of mica paper covers this chamber).
-->Microwave mica chips can effectively prevent water or oil and other substances from splashing on the magnetron or other components during the heating process of food. Protect the microwave oven from burning.
Warm Tips:
(1)Carefully measure the location size in your microwave and cut down to fit in the spot. Most microwaves have a slot or groove of some sort where you position 'tabs' in this paper to fit depends on the brand.
(2)This mica plate sheet can be used in many makes and models of microwaves and ovens and can be replaced normally as long as it is the same size and shape.
(3)Do not forget to clean the waveguide cover during daily cleaning, and pay attention to keep it clean and dry.
(4)Recommended to replace the mica sheet regularly, its quality directly affects the function and service life of the microwave oven.
Installation is pretty simple:
Step One:You pop out the old microwave sheet, get a pencil and trace the old shape onto the new plate sheet.
Step Two: Then cut along that shape, and pop the new sheet in.
clypek
Reviewed in the United States on November 12, 2024
We had a fire in the microwave and learned that this specialty item covers the microwave beam emitter (forgot the technical name of that item). I checked online and a with repair parts supplier. They wanted around fifty bucks for a replacement. I purchased these, cut one of them to the same shape, installed it and the microwave is up and operating again. You don’t need an appliance repairman to fix it for $150 or whatever. A good DIY job.
Selma A
Reviewed in the United States on October 2, 2024
I was able to use these plates to replace ones that had burned up. Easy to trim and works perfectly. I'm very happy with this purchase.
A C
Reviewed in Singapore on October 15, 2024
Works like a charm, but cutting may be challenging. Consider using a penknife rather than a scissorsMy Microwave is back working again!
Mona
Reviewed in Saudi Arabia on August 22, 2022
Good quality, price ,
Will Henry
Reviewed in the United States on March 18, 2022
My daughter let me know a few days ago that the microwave was scaring her. That did not sound good so I took a look and sure enough, large sparks and small fires were forming on the wave guide cover. A quick search on the web informed me that the plate needed to be replaced. I had never had to replace one of these before, and after measuring the old plate, I realized it was going to be difficult to find an exact match. So I went the universal route, making sure that the dimensions of the universal plate were larger than the full dimensions of the original plate. I received the wave guide cover quickly and they were sized correctly. I laid it behind my original plate and traced away. They appear to be of good quality and were fairly easy to cut with scissors and a utility knife for in-between the tabs. It was also easy to install. Now, my microwave works as intended and no longer scares my daughter... or me. Good product!
S. Kent
Reviewed in the United States on December 6, 2022
the package arrived safely. Four sheets. I traced what was left of the old broken one onto a 3x5 card, and trimmed it to fit perfectly, then used the 3 x 5 card to make a pattern on one of the four sheets. It cut easily with a sharp pair of scissors, and installed in about 5 minutes total. It cost about $6 to fix the microwave and it works perfectly. A factory mica was NLA and the old stock ones people wanted close to $50 with shipping so this was a great solution.
Gui Oba
Reviewed in the United States on June 30, 2020
Got a Mainstays microwave about a year ago and a few weeks ago it started occasionally jump-scaring my wife with loud sparks/arcs until eventually it started happening every single time we used it. Before we took the microwave in for maintenance, I decided to check online for alternatives and voila - found this cheap and easy solution. I wasn't sure if it was going to work, but a few weeks of daily usage later and no sparks! The boards were more than big enough and were easy to cut after tracing my original cover (just be careful not to bend it, it feels like it could snap). I couldn't see how badly burned it was until I saw the inside. I've included pictures of the before and after. I did slightly sand down the metal where it was burned using high-grit sandpaper, just to be sure there were no peaks, but I can't know if that made a difference.Bottom line: try this before repairing or getting a new microwave. It's so cheap, you don't really have much to lose!
Gino La Grache
Reviewed in the United States on May 28, 2020
When my eight year old Emerson microwave started sparking and doing what seemed like opening a new portal to another dimension, I was worried it was time to ditch it and get a new one. Well, after a little research on YouTube, I learned this happens when that paper-thin piece of cardboard (the one you always wondered what it did) becomes too soaked with grease and butter, and it starts to seep in to the motor on the other side. This piece is a protective barrier for the motor, preventing it from getting dirty or wet. When the motor does get wet, the debris conducts electricity and causes it to arc. This is VERY dangerous, but no need to worry, all you need to do is order these mica sheets. Then, you take out the old dirty one from the inside of the microwave and trace it with a pencil on the new mica sheet. Cut it with scissors and then insert it where the old one used to be. That's it! Saves you hundreds of dollars on a new microwave and also keeps another electronic appliance out of the landfill. Since my original mica sheet lasted eight years, this set of four should last you longer than you could ever imagine!
M. Phillips
Reviewed in the United States on February 17, 2020
My microwave's waveguide cover fell apart after years of use (I didn't even know what the piece was called or what it was for ... thank you internet, otherwise I would have purchased a whole new microwave). I couldn't find a replacement cover specific to my microwave model, but my search led me to these mica plate sheets.I cut a new cover out of one of the sheets, and when I realized it was still a little large, I trimmed it down. It was easy to cut and trim, and it has been working well in my microwave for 2 months now. I have tons of mica left over. A cheap repair that was simple to do.I am still going to give the review 5 stars because I only needed to use a small amount of the Mica, and have plenty left over..... BUT I WILL NOTE THE FOLLOWING: the product page said that this contained 4 pieces of Mica, but the package I received only had 3 pieces of Mica in it. I only used a portion of one sheet, and thus it wasn't worth me complaining to Amazon (since I have no need for the other sheets that I got anyway), but in case others are regularly getting shortchanged so to speak, I thought I'd mention here that I only got 3 pieces.
Kim
Reviewed in Mexico on December 8, 2020
Muy útil , está increíble que vengan más de un aditamento
Rob
Reviewed in the United States on April 1, 2020
My microwave was arcing with no metal or reflective surfaces in it. It turns out that little square on the side of your microwave is a wave director. Mine was stained and had a small hole in it. Be sure to not tear the old director when you remove it. They are flexible like cardboard so when you remove the old one and install the new one you can flex it to in place. My microwave did not have any screws holding it in place only guide grooves. Use the old director as a template to exactly cut out the new one's grooves. You can use a scissor to cut out the correct shape. Once the new one was in place the microwave works fine. $5 part or $100+ new microwave. Try this before buying an entire new unit.
Recommended Products