Your cart is empty.
Your cart is empty.
Installation Instructions:
1. Ensure your LED strip is 10mm wide and has 4 copper contacts at the cutting line.
2. Carefully cut your LED strip along the cutting line. Do not tear off the paper on the back of the LED strip before finishing the connection. Just insert the paper and the LED strip together into the connector. This will be easier to insert the LED strip into the connector without bending the LED strip into damage, and the connection will also be more stable.
3. Open the cap of the connector.
4. If you use a non-waterproof LED strip, please insert the LED strip into the connector. Make sure the 4 copper contacts on the LED strip are under the 4 electrical conductors in the connector;
If you use a waterproof LED strip, please first remove the waterproof silicone around the cutting line, then insert the LED strip into the connector. Make sure the 4 copper contacts on the LED strip are under the 4 electrical conductors in the connector.
5. Close the cap, and check whether the connector works well.
6. Tear off the paper on the back of the LED strip to stick the LED strip, but please reserve the paper that has already been in the connector.
Note:
Please make sure that the positive poles of your LED strips at both ends of the connector are on the same one channel. Please make sure the arrow marks on your cable, your LED strip and your controller are on the same one channel.
Solutions:
If the LED strips flicker or do not light up, please follow these steps:
1. Take off the LED strip from the connector.
2. Open all caps on the connector.
3. Use a thin and hard object to simultaneously press hard on both ends of each electrical conductor in the connector, to bring the electrical conductor down to the lowest position. Make sure the electrical conductor can touch the surface of the bottom of the connector without any pressure. In this way, the 4 electrical conductors in the connector can fully touch the 4 copper contacts on the LED strip, ensuring good electrical conductivity.
4. Insert the LED strip into the connector.
Package includes:
10x clasp connectors for 10mm wide SMD 5050 RGB LED strip lights
Messan
Reviewed in Belgium on March 9, 2025
Fonctionnel
Tonio Convertini
Reviewed in Italy on March 26, 2025
Mi ha aiutato molto ho recuperato una striscia led persa
YoYo
Reviewed in Germany on February 22, 2025
Durchgerissenen 15m LED Streifen gerettet ohne kleben o.ä.Super
Robert
Reviewed in the United States on January 6, 2025
They worked perfect. Exactly like I needed them too.I used it to repair a broken “neon rope“
Ken
Reviewed in the United States on September 14, 2024
Little tricky to get it to work. However it comes with a lot and once you get it on and working it stays
Jörg
Reviewed in Spain on August 24, 2024
Los conectores de 4 pines para tiras LED cumplen perfectamente su función, comprobar primero si se ajustan a la medida de vuestras tiras. Son fáciles de usar y te aseguran una conexión firme sin complicaciones. Contento con el resultado, recomendable.
Taha S.
Reviewed in the United States on March 30, 2024
Waste of money and efforts. Doesn’t work at all. Also I almost cut my finger trying to undo the clip which extremely tight.
Lizzy's gurl
Reviewed in the United Kingdom on December 19, 2024
They work well if your trying to add a few short strips together , but if your trying to extend a 10m cable don't bother . I think it's more to do with it being the maximum length of the cable than the connectors themselves
Ariel Ortega
Reviewed in the United States on December 16, 2024
buena calidad, bastantes utiles para unir varias tiras leds
RJ
Reviewed in the United States on December 10, 2024
Works great, does what is supposed to, looks good, blends well
Angelo
Reviewed in the United States on May 21, 2023
They're tough to open and really pinch on the ends of the golden contacts of the LED strip, which may affect your pins at the end of the LED strip & contest the efficiency of your lighting connection.
Christopher Harrison
Reviewed in the United States on July 31, 2021
Really difficult to get the Led Strips to stay place they kept falling out of connectors
Recommended Products
