Your cart is empty.

2 3/4' Carbide Hole Saw with Arbor and 12' Extension for Drilling Deep Holes 7/16' Hex Arbor and Extension

5.0 Write Review

Free shipping on orders over $29.99

$57.95

$ 28 .99 $28.99

In Stock

Qty.:

About this item

2 3/4" 70mm CARBIDE GRIT HOLE SAW KIT For Drilling Holes In Abrasive Materials, A Regular Toothed Hole Drill Bit Would Go Dull Used As A Concrete Hole Saw But With The 7/16 Hex Arbor And the TCT Carbide Tipped Tool Bit This Tungsten Hole Saw Comes With it can Drill through Brick and Masonry with Hammer Drill Setting.
TUNGSTEN CARBIDE GRIT Hole Saws Are Professional Tools Construction Tools Electrician Tools And Plumbing Tools Whether It Be For Diy Home Improvement Or Remodelling. Drill Holes Through Brick Walls To Run Conduit For Electric Cables And Pvc Water Pipes And Waste Pipes.
Heavy Duty 7/16 Hex End Arbor for Hole Saws 1 1/4" to 6" inclusive comes with TCT Pilot Drill for Drilling Masonry.
Drill Long Reach Extension for Drill Bits with 7/16" Hexagonal Shaft 12 inch Extension Drill Bit Heat Treated Hex Drill Extension
Hole Saw Bit Extension for Concrete Hole Saw 12" Long 7/16 Drill Bit Extension Kit 7/16" Hex Male To 7/16" Hex Female Drill Extension 7/16" (11mm) Hex Arbor Hole Saw Extension Set Hex Key Inc 12 Inch Drill Bit Extension Shank

Product Description

Tungsten Carbide Grit Edge Hole Saw and Accessories

Carbide Hole Saws for Concrete and Drywall

Carbide Hole Saw Tungsten Carbide Grit Edge. Serrated Edged Teeth Hole Saw Capable of Drilling Concrete Drywall Brick and most Masonry Products. No Teeth to Dull and Bind. Must be used with Hammer Drill and TCT Tipped Pilot Drill.

Hole Saw Arbors with TCT Pilot Drills Are Suitable for These Size Carbide Hole Saw

Hole Saw Arbors / Mandrels Suitable for use with Larger Carbide Grit Hole Saws have Tungsten Carbide Tipped / Masonry Pilot Drills which can be swapped out for High Speed Steel Pilots if you use them on non Masonry Products Later. 7/16 Hex End Asin: B08NT2P715 OR SDS Plus End ASIN: B08NHMWY9S

7/16" Hex Female to 7/16" Hex Male 12" Hole Saw Arbor Extension

7/16" Hexagonol Ended Hole Saw Arbor / Mandrel Extension is Suitable with any 7/16" Hex End Arbor - Extends Drilling Capabilities an extra 12" Deep. Fits any regular 1/2" wide opening Drill Chuck. ASIN B08NHB1T2R

7/16" Hex Female to SDS Plus Male 12" Hole Saw Arbor Extension

The SDS Plus Male end of this Arbor / Mandrel Extension Means this Arbor must be used with an SDS Plus Type Drill. The Female end that Connexts to the Hole Saw Arbor is a 7/16" Hex End so the Hole Saw Arbor must Also have a 7/16" Hex End - Extends Drilling Capabilities an extra 12" Deep. Fits SDS Drill Chuck Only. ASIN B09S8MHFN2

Tungsten Carbide Hole Saws Material Cutting

Holes in Cement Block

Must use Hammer Drill and Must use TCT Pilot Drill for all Masonry Products.

Holes in Concrete Pavers Block and Coping

For Deep Holes Break Core out when Hole saw bottoms at 1 1/4" Deep, this allows Hole Saw to continue. Regularly check for TCT Pilot Drill not worked loose, a loose pilot will prevent the hole saw from cutting.

Cut Hardie Board Drywall Marble Slate Cement Board Drywall

Pilot Drill can be replaced and or swapped out for a HSS Pilot Drill if Drilling non Masonry Products like Plywood. TCT Pilot Drills are only for Masonry Products.

Serrated Teeth Covered with Tungsten Carbide Grit

Can be used with SDS Plus or Hex Arbors.

Shopping Cart