Your cart is empty.
Your cart is empty.Are you still worried about the time-consuming preheating of 3D printing, poor material adhesion, and many printing failures? Try our GECO plate, which is tailor-made for PLA materials and a new printing experience will start immediately! No Heating to preheat the hot bed, only 1°C micro-temperature is required, which saves energy and electricity, and the printing cost plummets. It is a must-have for agricultural printing enthusiasts! Whether you are a novice or an expert, the first layer has super strong adhesion, and it is sticky at room temperature above 0°C. No glue spray is required, and the printing process is simplified. What's more surprising is that it is thicker and more durable than ordinary PEI hot beds, magnetic anti-warping, double-sided design, flexible disassembly, and spring steel plate for easy mold removal, and the printing experience is fully upgraded! Note: Although it is advertised as "no heating", it is recommended to increase the temperature to 20-40°C in low temperature environments (below 20°C). For large or batch printing, you can add a brim or increase the temperature. Daily maintenance is super simple: alcohol or soapy water can be wiped clean, and after long-term use, 55°C heat treatment can restore the stickiness to its original state. Compatible with many popular models of Bambu Lab (X1/X1C/X1E/P1P/P1S/A1), 257x257mm platform is perfectly adapted, sci-fi texture surface, the bottom of the print is exquisite and uniform, beauty and strength coexist! GECO board makes every print a pleasure!
abassham
Reviewed in the United States on May 29, 2025
The Kobra 3 and Kobra S1 series can't go below 45c on the hot plate setting and this will lead to super adhesion with it being very difficult to remove your PLA from the plate. You can set the slicer to1c and as long as you don't touch the controls on the printer itself, it will "mostly" stay at ambient temp. They should put this in the AnyCubic specific plate descriptions.
Aero Engineer
Reviewed in the United States on May 26, 2025
I've got about 10 prints in with PLA and it seems to work as advertised. I got this because my BIQU plate stopped gripping after a couple months regardless of how I cleaned it.I'll update my review if this changes after a few months.
Caribulou
Reviewed in the United States on May 22, 2025
This is a great build plate. It requires no head just room temp and holds PLA prints firm with no adhesion issues.
Christian P
Reviewed in the United States on May 20, 2025
Set the temperature to room temperature, experimented with 0c, 1c, 30c and no PLA would stick to the plate. I tried several different rolls, some straight out of the dryer with no luck whatsoever. I just went back to the stock plate and had no issues. Maybe it works for some but I was unable to make any PLA stick to it after following the instructions unfortunately.Update: Had to set it at exactly 40c to get it to work, so it does actually work and works well, I would just recommend a more thorough how to use them is given out of the box currently.
R Wood
Reviewed in the United States on May 16, 2025
The media could not be loaded.
AxiomXIII
Reviewed in the United States on April 30, 2025
First, to answer the obvious question. Yes, this does work without heating the build plate at all. I use Bambu Studios with all of my Bambu printers, and I have created custom profiles for my most commonly used filaments that have the temperature set to 1 degree Celsius, (well below normal room temperature). I have had no issues with prints adhering since switching to these plates. No more glues, no more hairspray, just perfect prints. It has been wonderful. I haven't really tracked wether this is having an impact on the overall cost of operation of my printers, but I don't see how it can be hurting. I might also mention that I used to have some experience with heat creep when using PLA with my X1C, and that has disappeared completely. (I know that this was mostly caused by user issues and not having my settings dialed in 100% but this plate has still helped.)Perhaps the best recommendation I can give for this product is that I received one from Vine for review and almost immediately purchased another for my other printer. Highly recommended.
ServerGoon
Reviewed in the United States on April 29, 2025
I used the standard cool plate profile for the X1C and this thing really sticks. I was printing 4 items at a time that had some supports built in and the supports are still on the plate. You can see the supports as small circles on the plate. In fact I gave up trying to get them off and will have to hunt down a better scraper. I'm hoping not to destroy the plate.The plate feels thicker and heavier than a stock textured and I'm really impressed with the adhesion. Once I have it cleaned off, I'll certainly use it again for projects that have a small contact are that also don't need supports. Good purchase, fairly pricedBambu Lab X1CCold Plate SettingsTri Color PLA
Peverell
Reviewed in the United States on April 29, 2025
I’ve sent several prints through this plate and every one has been perfect.PLA and PLA+ stuck and released perfect. PLA silk stuck a little too well to where it tried to rip the bottom layer off the print. So use silk at your own risk.I’ve set the temp to 1, 20, and 25C and each print has stuck well.Set plate to textured.Highly recommended so far.
Recommended Products
