Your cart is empty.
Your cart is empty.Dakota
Reviewed in the United States on June 18, 2024
It's usually hard to fault an FPV drone frame for breaking.. kinda comes with the territory of the hobby, but this frame broke on the first crash. I got hung up in a tree and disarmed 14-16 feet above soft dirt and an arm snapped on impact. There are two holes on each arm that don't seem to serve any purpose other than to severely weaken the arm and make it more prone to snapping. Really wishing it came with extra arms to take advantage of how replaceable they are. Also, there were no screws for the red standoffs, so I was lucky to have 16 M3 screws laying around otherwise I wouldn't have been able to build it. Aside from those compliments, the frame is very spacious with room for any set up you could want and I like how the arms are replaceable.
Kirk S. Nelson
Reviewed in the United States on July 26, 2020
For the money this is a nice frame set. Good quality carbon, all the standoffs and hardware were complete. I would purchase this again. Kirk
zachary
Reviewed in the United States on September 11, 2017
I love this frame, it refuses to break. I've smacked it into so many things and after eight months, it's just starting to flake. It had all parts and easy instructions. But, the little legs really suck. They don't stay it one place, and honestly look awful. So I just took them off. Wonderful frame. Very spacious.
Dippeggs
Reviewed in the United States on May 27, 2017
Great frame, very sturdy. I haven't flown yet but i can tell its very strong. All the screws and nuts were in it. The carbon fiber is machined great, but a little dusty so make sure to clean the plates before you assemble it.Im taking 1 star away because the red standoffs I got with mine were the wrong size. All but 1 were too small.Because of this, i wasnt able to use the camera plate that goes in the front. Also mounting my camera was a bit tricky, but i blame my 1 screw mount for that.Word to the wise, install the red standoffs before you attach the legs. Or else you'll have to take the whole thing apart towards the end, like i did.
Bryan
Reviewed in the United States on January 24, 2017
Once put together the quad looks amazing, seems very well cut/laid out. However the instructions call for screws that it can't be put together the way it shows in the instructions. Otherwise though it seems like a good design!
RobotSpider
Reviewed in the United States on December 25, 2016
Parts are fine in themselves, but it comes with the wrong screws. The directions indicate it comes with 16 3x6mm and 16 3x10mm, which it does. But after using the 16 3x10mm screws to attach the arms, the 6mm aren't long enough to attach the upper part to the lower frame body. This kit has obviously never been assembled by the manufacturer or it would have been obvious.The carbon fiber is good quality. Just wish it had the right screws.
Starsapphirez
Reviewed in the United States on October 16, 2016
Very good frame for its cost. It took a little while to put together but it was worth it. Not much effort involved. It feels to me like genuine carbon fiber. I do not expect the arms or body to break. The pieces that hang from the arms are a little weak and will break in a crash, but if you can reinforce or remove them then they should not be a problem. I have tried a few motors and they all work. There is enough space to mount esc's, although it will take some DIY innovation. Standard flight controllers (Naze, CC3D...) and PDBs will work. Also enough room to mount all other necessary parts for FPV transmission. I would recommend this product.
Victor
Reviewed in the United States on January 28, 2016
Overall: Good price and durable, but may need some refining.The good:1. The frame is very strong. It might be a little heavier for it, but as a beginner frame durability is definitely more important than lightweight. I have had some large impacts and the frame is just fine (wish I could say the same for my video transmitter :'( )2. All necessary hardware included. Seems like it should be obvious but cheap bargains can often cut corners and leave things like hardware out.The bad:1. The slots for the motor mounting screws are too narrow to fit the standard M3 screw size; I had to use a dremel to widen the slots a bit in order to mount my motors. Not a huge deal, but it might be a PITA if you don't have the right tools.
Recommended Products
