Your cart is empty.
Your cart is empty.Product Description
KINGMODEL Dual Way Bidirectional Brushed 5A ESC 2S-3S
Kindly Note: DO NOT use 4s battery, and above 5A will burn out the ESC! The KINGMODEL Dual-way Bidirectional Brushed 5A ESC is small size Bidirectional Brushed 5A ESC, widely used for 1/35 RC model cars,tanks, 4WD RC cars etc. Compatible with 130 180 Brush Motor, it can be go forward and backward freely. In the mixed control mode, can make a double-motor differential turn boat, tucker, tracked vehicle, etc. It is just a good job man!
Specification
- Product Name: Dual-way Bidirectional Brushed 5A ESC.
- Power supply: 2s / 3s lithium battery (DO NOT USE 4S).
- Output current: 5A x 2.
- BEC: 5V 1.5A.
- Board size:36x26mm.
- Mode can be adjusted: mixed/independent.
What's in the box?
3pcs x Dual-way Bidirectional Brushed 5A ESC.
- More tips:
- Power-on prompt: The PWM remote control quantity is 1500, which is the middle position of the throttle. The ESC will be unlocked, you will hear the motor beep, and the ESC will start.
- The signal is abnormal: S1(PWM) signal is greater than 2.1MS or less than 0.9MS, abnormal signal is equivalent to signal loss.
- Out of control protection: If the signal is lost, the throttle needs to be returned to the center and unlocked again for safety and motor protection.
- Over current protection: 130 degree overheat protection, and hardware over current protection.
- Power-off protection: Power supply voltage is lower than 4V, ESC restart protection.
Main features
Please Note: It can not use 4s battery, and above 5A will burn out the ESC.
- Power supply: KINGMODEL dual-way 5A Brushed ESC supports 2-3S Lithium battery.
- Adjustable mode: Dual mode switch switching: It can adjust the differential turn of the two motors, or control the forward and reverse of 2 motors separately. In the mixed control mode, can make a double-motor differential turn boat, tucker, tracked vehicle, etc.
- Performance: Good heat dissipation and power indicator: built-in capacitor module strong resistance current capability, also with red power led indicator.
- Multiple Protections: No more worry about losing overheating (130 degrees), over-current, loss of throttle signal, the 5A brushed dual-way Bidirectional ESC has been fully considered.
- [ NOTE! ] It can not use 4s battery, above 5A will burn out the ESC, 130 180 brushed motors are recommended. And Power supply should be 5V and signal input is PWM if not work well.
Hugh P.
Reviewed in the United States on July 2, 2023
I used a couple of these on different 150g robots. Definitely kinda big for that size robot
Same flyer different airspace
Reviewed in the United States on May 30, 2023
Seller sending 3 pack to replace bad one due to manufacturers defect
DJ
Reviewed in the United States on May 1, 2023
This one is niiiice for low power hobby motors. Switches forward/reverse or left/right without any delay or glitching. Using it with a Radiolink AT9S Pro transmitter and R6DS micro-receiver. Figured out it includes a 5V BEC output (which isn't advertised) to make my project even smaller. Ran both 130 and TT motors for about 15 minutes. The ESC, receiver, & motors were cool to the touch. The motors were also much quieter compared to a different ESC. This thing performs like a champ for small motors! I just started in the hobby so don't have any bigger motors to throw at it. I'm trying to build a micro crawler tank where even 130 or TT motors are waaay more power & torque than I need.Also they come in a pack of 3 which means you can drive 6 motors as long as your receiver has enough channels. The single pin for the secondary slave motor works well. Positive & negative for the yellow wire are unnecessary as long as you have your transmitter configured to a master>slave for the 2 channels these will use.I'm EXTREMELY happy with this purchase. Finally a good solid dual ESC + BEC for small hobby motors that behaves well and stays cool. No external BEC is required helping cut down space for micro projects.
Recommended Products