Your cart is empty.
Your cart is empty. 4.3inch Capacitive Touch Display with Protection Case for Raspberry Pi 4B, 800×480 Resolution, IPS Wide Angle, MIPI DSI Interface.
Features
1) 4.3inch DSI LCD, IPS screen, 800 x 480 hardware resolution.
2) Capacitive touch panel, support 5-point touch.
3) Tempered glass capacitive touch panel, hardness up to 6H.
4) DSI interface, refresh rate up to 60Hz.
5) Supports Raspberry Pi 4B.
6) Supports Raspbian, 5-points touch, driver free.
7) Supports Ubuntu / Kali / WIN10 IoT, single point touch, driver free.
8) Supports Retropie, driver free.
Hardware connection
Connect the DSI interface of the 4.3-inch DSI LCD to the DSI interface of Raspberry Pi.
For easy use, you can fix the Raspberry Pi on the backside of the 4.3inch DSI LCD by screws.
Software setting
Supports Raspberry Pi OS / Ubuntu / Kali and Retropie systems for Raspberry Pi.
1) Download the image from the Raspberry Pi website.
2) Download the compressed file to the PC, and unzip it to get the .img file.
3) Connect the TF card to the PC, and use SDFormatter software to format the TF card.
4) Open the Win32DiskImager software, select the system image downloaded in step 2, and click 'Write' to write the system image.
5) After the programming is completed, open the config.txt file in the root directory of the TF card, add the following code at the end of config.txt, save and eject the TF card safely.
6) Power on the Raspberry Pi and wait for a few seconds until the LCD displays normally. And the touch function can also work after the system starts.
Online Development Resources /User Manual:// bit.ly/45SQ41r
Package Content
4.3inch DSI LCD x1
3D-Printed Case x1
Cooling Fan x1
Screws pack x1
Screwdriver x1
ANONYMOUSAMAZONCUSTOMER
Reviewed in the United States on June 1, 2024
Could not power up, no matter what combination of Pi, cable and power cords I used. Spent four weeks going back and fourth with Waveshare support, being asked repeatedly to make sure I used THEIR software and that would fix the problem. (Hard to use software when the screen DOES NOT POWER UP). After finally admitting it was dead, Waveshare decided that since I didn't buy it from them, they weren't responsible for it. Of course, they waited long enough that now I can't return it. So I'm out $70 AND still need a screen.Horrible customer support, bad product. Sadly, Waveshare doesn't get the hit, this company does, because I can't leave Waveshare a negative review directly.
Cedric Chase
Reviewed in the United States on December 16, 2024
Like some other reviewers - I thought the screen was DOA, but be sure to check the documentation they've linked. You need to paste a couple of lines in the config.txt file for it to work. This is what worked for my Pi 3B+, no parenthesis: (dtoverlay=vc4-kms-v3d#DSI1 Usedtoverlay=vc4-kms-dsi-waveshare-panel,7_0_inchC,i2c1)
John Clark
Reviewed in the United States on December 1, 2023
A bit more than I wanted to pay for just a bare screen. I had problems getting it to work with octopi, but I downloaded a new version of the desktop os and it came up fine. There is no information included. It would be nice if there was something. Has a problem with hanging the pi when doing apt updates. Vendor refunded money.
CoolRodz
Reviewed in the United States on June 15, 2022
I purchased this screen to use in the SmartiPi Touch Pro - Case for The Official Raspberry Pi 7" Touchscreen Display and it fits with some alterations to the case to get everything to line up. Once everything was mounted getting this "Plug & Play" screen to lightup took a lot of research and additional coding to come alive. This only AFTER loading the proper drivers from WaveShare for this specific screen, as the plain vanilla waveshare drivers WILL NOT WORK! .Then the real problems began, getting it to flip 180 so it would read properly with my mounting setup. While I was also dealing with a learning curve with Raspbian Buster (Octopi) coding I finally got it to rotate 180 with the correct command in the cmdline.txt files (video=DSI-1:1024x600@60,rotate=180) and the touch to function properly with the correct command in the config.txt file (dtoverlay=WS_7inchDSI1024x600_Touch,invertedx,invertedy). Of course all this is easier if you use the Raspbian Bullseye OS with the desktop & it's menus rather than having to use the Octopi OS with no desktop and doing the coding via SSH when using it for a 3D printer Control! It's a really nice screen for the $ spent and the touch works sweet compared to a resistive touch screen!
tbraf
Reviewed in the United States on April 30, 2022
DOA, Driver board ok, display dead. Spend a little more for certified parts .
Recommended Products
$28.00
$ 13 .99 $13.99