Your cart is empty.
Your cart is empty. 1.Heatsink Kit 40x40x11mm Thermal Conductive Adhesive Tape,
2.Cooler Heat Sink for Cooling 3D Printers, TEC1-12706 Thermoelectric Peltier Cooler
3.40mmx40mmx11mm Heatsink
Rabid
Reviewed in Australia on July 25, 2024
Bought these to stick to my Ender 3 Max's stepper motors. Work well. Stick even better.Make sure your surface is clean and that you've got them where you want them to be forever. I think it'll take some effort to remove these should that day come.If you need some small adhesive heatsinks these will do the job.
Mark
Reviewed in the United States on July 15, 2024
They’re the perfect size for the motors on a 3d printer however I could only install them on 2/4 motors because the gantry and hot bed would collide with them when moving.
David A
Reviewed in Canada on November 15, 2024
Stuck these on a PSU that was getting a little too warm causing the fans to spin up loudly. These helped quite a bit.
5port
Reviewed in the United States on April 28, 2024
Stuck three of these on the back panel of my active speaker because it had a very hot spot. No more hot spot and back panel just feels warm now. They work. They stick well to a smooth surface. No guarantee on a rough surface.
Michelle Hart
Reviewed in the United States on May 6, 2023
Easy to install, hard to take off
TK4619
Reviewed in the United States on November 10, 2023
Placed all 4 of these on my Xiegu X6100 because it gets hot when in use. These have made a huge difference in the temp of the radio. Now while its very warm its not too hot to handle it.
robert drake
Reviewed in the United States on August 28, 2022
One came with bent fins. I'm sure it'll still work fine but still. Other than that, good quality.
dominic oppedisano
Reviewed in the United States on May 14, 2022
I placed these onto my Ender 3 and haven't regretted it. They work perfectly at dissipating heat. The stickers are nice and thin to very well transfer heatNot the product's fault, but couldn't put them onto the back of every motor due to the size of them hitting the y moving gantry, and the Z bottom being against the base. I've placed them on the side instead which still works great.Also if you want to unstick the stickers, I let isopropyl alcohol soak into the edge to release it after noticing my Y axis hitting it due to the position I placed it. Worked fine after.
Dustin Widmann
Reviewed in the United States on March 16, 2022
As advertised. No obvious defects in craftsmanship nor shipping damage. The preapplied thermal adhesive seems to hold pretty well, so far anyway. Supplied dimensions were within tolerances of what was specified. Sinks heat. Dirt cheap. What's not to like?
カスタマーマ
Reviewed in Japan on August 7, 2021
クロームキャストが調子悪くて貼ってみました。貼ってからは安定しています
OnlineShopper
Reviewed in the United States on December 20, 2021
Good quality overall and strong included adhesive tape. One of my pieces was bent (one or two fins), but I only needed 3 pieces for my 3d printer stepper motors so I straightened the bent fins of the fourth piece and save it as spare. Recommend for the price.
むるち
Reviewed in Japan on August 30, 2019
ＨＤＭＩからぶら下げるファイヤーＴＶの受信機（旧タイプ）が熱でフリーズする事が多々ありましたので放熱させるために両面に貼り付けました。効果はあるようです・・・
Recommended Products
$25.99
$ 11 .99 $11.99