Your cart is empty.
Your cart is empty. Product Detail:
90mm length Hexagonal handle drill chucks Clamping range: 0.3 mm-6.5 mm with 1/4”（6.35 mm） Black
57 mm length Hexagonal handle drill chucks Clamping range: 0.3 mm-3.6 mm with 1/4”（6.35 mm） Black
61 mm length Round handle drill chucks clamping rang:0.3 mm -3.4 mm with 1/8" (3 mm )shank White
59 mm length Round handle drill chucks clamping rang:0.3 mm -3.4 mm with 1/16" (2.35 mm )shank White
Package:4 PCS Keyless Drill chucks
Jörg - Jürgen Schwermer
Reviewed in Germany on February 27, 2025
Bohrfutter
laurent MIGNARD
Reviewed in France on February 10, 2025
correspond parfaitement à mes attentes
Sammy T.
Reviewed in Canada on January 5, 2025
Its usefull, easy to use.
frichet jacques
Reviewed in France on December 8, 2024
bien reçu. Ok.
Stan
Reviewed in Canada on October 30, 2024
holding small dremel bits
Tony S
Reviewed in the United States on April 28, 2024
that was able to hold smaller bits, really small bits.
ken jones
Reviewed in the United States on February 11, 2020
Poorly made
Handlebar
Reviewed in the United States on January 18, 2020
These chucks align a bit to run true. My previous chuck purchased several years ago allowed the bits to wobble when tightened. These chucks do not, and should work for anyone doing small semi precision jobs.
The D
Reviewed in the United States on July 18, 2019
I received a set of items as pictured and expected. The review talking about how poor the quality was and mentioning “runout” or the amount off center the item causes in effect, I did not experience a noticeable amount of runout due to poor quality.Whenever you add an adapter to a Chuck, and I don’t care what application you are using be it a drill impact or dremel/ other power tool: whenever you add an accessory or adapt a chuck or otherwise in this lot listing you can expect a little runout for obvious reasons. Again in my case I had an almost true end drill point and was pleasantly surprised having fears from the prior review. I guess it was a bad batch prior or user error possibly if he didn’t seat the chuck right but I’m assuming he is (sounding) well competent and aware of these things and will default to China for poor quality. Good news is based on my batch they have addressed that quality issue
robert clark
Reviewed in the United States on December 15, 2019
Good little set of adapters . I bought a set for work ... Very handy however the biggest one isn't very big...
solitude
Reviewed in the United States on October 24, 2018
Do not buy!!!! 1 use and the ends where it clamps down on the bit/accessory friggin broke. On 2 of the 4. I havent used the other 2 yet but im sure i will get the same result
F. Brewer
Reviewed in the United States on September 7, 2017
Sigh -- run out is staggering on these. 1.0mm bit at 2cm makes a 2.5mm circle for the smaller chucks (ca do better wrapping cellophane tape on the bit and than chucking it in 1/16 capable, but square, chuck. Materials are very soft but the arbors are well made and square. I may well replace base seat on two of these with steel part (given I find the time). If you are looking to chuck small bit on a drill press, better look for a JT0 Jacobs 1/64-1/4 chuck... $59 or so. I don't understand the lack of inexpensive small chucks and pin vices -- for PCB use, use carbide bits and collets.
JP
Reviewed in the United States on December 15, 2017
Works great. I have a lot of small drill bits which are impossible to use in a normal chuck for a desktop drill press. These did the trick.
Recommended Products
