Shopping Cart

Your cart is empty.

Your cart is empty.

ACC Automotive Carpet Compatible with 1960 to 1966 Chevrolet Standard Cab Pickup Truck, 2 WD Automatic (3in Low Tunnel) (557-Gunmetal 80/20 Loop)

4.3 (6) Write Review
Free shipping on orders over $29.99

$207.95

$ 90 .99 $90.99

In Stock

1.Color:501-black 80-20 Loop


About this item

  • This item is made in 557-Gunmetal 80/20 Loop carpet. The item image may be a different color, but the SWATCH image is the correct color. Carpet Fits 2 WD Automatic (3in Low Tunnel). Unless otherwise noted, the jute padding is heat bonded to the backside of the carpet and a heel pad is welded to the correct location.
  • Holes may not be cut in automotive carpet and carpet may require trimming to install. PLEASE FIND THE INSTALL INSTRUCTIONS ON THE HELP TAB IN OUR STORE DETAILS PAGE.
  • Automotive carpet compatible with Chevrolet Standard Cab Pickup Truck will be Heat and Pressure formed using a form that was created from the original floor pan. Carpet is guaranteed to fit to the floor when installed correctly.
  • All automotive carpets are Made in USA with Top Quality auto carpet materials. IF YOU ARE NOT 100% SURE OF THE COLOR/MATERIAL YOU NEED, PLEASE CONTACT US BEFORE ORDERING.
  • Automotive carpet will fit just like original carpet when installed correctly and is Guaranteed against Defects. This item fits the years: 1960 1961 1962 1963 1964 1965 1966


  • This automotive carpet will be made in 557-Gunmetal 80/20 Loop. Other colors and materials may be available in the selection above.
  • This aftermarket carpet is a replacement for 1960 to 1966 Chevy Standard Cab Pickup Truck, 2 WD Automatic (3in Low Tunnel).
  • Carpet will be made with standard flexibe polyethylene backing. Contact us to upgrade to massbacking
  • Unless specified, the jute padding will be attached in the foot area of the carpet
  • Installation may require trimming around the edges and the holes may need to be cut.
  • There is a large variety of colors available. Please request free samples if you want to match a specific color
  • This item fits the years: 1960, 1961, 1962, 1963, 1964, 1965, 1966, 60, 61, 62, 63, 64, 65, 66

READ FULL INSTRUCTIONS BEFORE BEGINNING - Instructions may vary for multi-piece sets

1. Remove new product from box. Lay flat and pop contours back into place. Allow a few hours for product to relax back into proper shape. Check material for accuracy
2. Compare new and old carpet
3. It may be necessary to use old carpet as a template for console cuts
4. IMPORTANT: Fold new product in half from front to rear. Place in vehicle lining up molded contour to seat risers or any other identifiable starting point. Once fitted, continue installation
5. Roll product forward make cuts for brackets, shifters vents etc while maintaining proper alignment on seat risers or other starting point
6. Cut in center at firewall to allow product to go underneath dash
7. Continue same procedure for remainder of installation – working your way to outer edges
8. Once product is properly fitted you are now ready to do the final trimmings on outer edges, seat belts and holes etc.

Note: If adhesive is desired, only apply a light brush or spray adhesive after correct dry fit has been obtained.


jasmine heyd
Reviewed in the United States on March 21, 2025
Just as described
mike
Reviewed in the United States on October 31, 2024
None of the carpets fit and although it says it’s returnable the $150 shipping fee makes it not worth the risk.
Heath Hallman
Reviewed in the United States on April 8, 2023
The carpet was not wide enough between the kick panels, which i saw on others reviews but decided to take the chance. It will not be wide enough. You will have to cut excess off the back, cut the trim around the outside of the carpet up front, and seam them both together. Not What i wanted to deal with in getting a new carpet that is supposedly molded to fit my pick up.
ANITA J VALLADARES
Reviewed in the United States on August 31, 2022
Very thin
Mike Cullum
Reviewed in the United States on June 5, 2022
Carpet was cut short on passenger side
Harold
Reviewed in the United States on October 14, 2022
Couple things… the width of the front area is too short. Also the firewall area doesn’t match the contour very well. The trim is of poor quality and not sewn well. My advice is to leave the width uncut and straight cut the firewall area. Let the customer cut it down to size. Carpet form was close but not deep enough. I made it work but had to splice.