Your cart is empty.
Your cart is empty. The high waterproof grade PoE Splitter is made of durable material and 4N Oxygen-free Copper. It is one-piece injector molding and featured with slot type structure, waterproof jacket is optional, can be used indoors or outdoors. It can separate the power and data via cable transmission. Proper matching use with POE switch or PSE injector which meet standard IEEE802.3af, provides 12V power and 10/100M data at the same time for the terminal device does not support PoE so that non-PoE devices can be powered over Ethernet.
Specification:
1. Input: RJ45 female
2. Output: RJ45 male and 5.5x2.1mm male DC jack
3. Data rate: 10/100Mbps
4. Maximum Power: 15.4W(IEEE 802.3af), 25.5W(IEEE 802.3at)
5. Voltage input: 48-55V, overvoltage protection
6. Voltage output: DC 12V
7. Current output: 1-2A
8. Maximum transmission distance: 150-Meter
9. Operating temperature: -20 Degree~50 Degree
10. Plug and play, no configuration required.
Applications:
1. Use with IEEE 802.3af standard power supply equipment (POE switch) and Non-POE device.
2. Unable to use with Non-POE switch or POE device.
3. It eliminates the need for a power supply or for a camera to be located near a power outlet.
Q&A
1- What is PoE?
Answer: Deliver power and data with a single Ethernet cable for fewer wall plugs and messed cables. Extend powerline to where no AC outlets are nearby, up to 300 feet away from the power source.
2- Why PoE to RJ45?
Answer: A cost-effective way to add plug-and-play PoE support to 12V powered devices and make full use of PoE switches.
3- What else needed?
Answer: You need an IEEE 802.3af compliant PoE switch or injector to serve as the PSE (Power Source Equipment) and an Ethernet cable with PoE signal to feed the splitter.
Dennis S.
Reviewed in the United States on March 19, 2025
I have bought a bunch of these for my home security setup and my permanent lighting / Christmas light show.I know that sounds funny but I run POE switches that run the lighting controllers on my house. Unabl I split the 12 volts/Ethernet into the controllers.I also run my cameras around the house. They work great. If anybody is interested I'm using the tapo pan tilt cameras.I will say that I had two randomly die on me. That's the reason for the four stars. I don't know why they would die. But I bought others and replace the broken ones. None of them have died at the same time so that's been good. One did die when we lost power so maybe there was a surge. Overall I like these and I will continue buying them.
Trelane Esq
Reviewed in the United States on March 17, 2025
These convert 48V PoE power to 12V barrel connector power.I'm using them to run non-PoE cameras and they work great.The only WARNING: The plastic clip on the RJ connector is a bit brittle. If you bend it too much, it breaks off.
Drew
Reviewed in the United States on January 29, 2025
Worked great for adding a poe wired outdoor camera. build quality seems good and allows power and connectivity. was easy to install and a good value.
TJG
Reviewed in the United States on December 21, 2024
Installed these on my security cameras and the work as they should. They are a little shorter than other PoE splitters but for me that worked out good. They have been installed for 3 weeks now in temps down to 0 and are working fine.
SonjaDCUSA
Reviewed in the United States on December 10, 2024
Inexpensive, they power a Boavision PTZ through POE replacing the need for a higher cost power extension cable.
Scott
Reviewed in the United States on October 28, 2024
One of them died, so I order these replacements. They work well with my Hiseeu cameras. You need to make sure you seal them correctly as water will kill them!
Just Saying
Reviewed in the United States on January 11, 2024
Mounted the splitter under the eve of the roof and so far so good. Price is right and I have a spare.
oholic
Reviewed in the United States on August 26, 2023
These seam to work great with a couple of non-POE IP cams of mine. I do question the waterproofness though. The main unit seams fine but the end assembly that waterproofs the incoming Ethernet seams poor quality and might resist a light rain. We get some really heavy rain from time to time so I guess time will tell. The problem with water getting into the incoming Ethernet connection is with POE power flowing the pins corrode quick, build up heat and start to fail. Also don’t like that there is not waterproofing provision included for the Ethernet and power outputs.
Recommended Products
