Your cart is empty.
Your cart is empty.Beguiled by a fancy new chip that is only available in a SOIC or MSOP/(T)SSOP pinout? This breakout PCB set will make your life much much easier and get you prototyping faster than ever. One side has a 8-TSSOP/8-MSOP pin out with traces going to two rows of 0.1" spaced holes, the other has 8-SOIC. Solder your chip to either side and you're ready to rock on any solderless breadboard.
Joseph J. Blavatt III
Reviewed in the United States on September 3, 2024
I support an engineering department and these PCB's are very useful in R&D work.
Andrew Ferg
Reviewed in the United States on November 5, 2024
Just right
pitsoft21
Reviewed in Germany on November 18, 2023
2 Sachen fand ich nicht gut:- die Einzelplatinen gingen nicht per Hand abzubrechen, es musste eine Dremel Flex benutzt werden- Pin 1 der Chipfläche war beschriftet, aber die zugehörigen Löcher für die Anschlüsse nicht. Das birgt ein Fehlerpotential
P. Meyer
Reviewed in the United States on February 25, 2022
Nothing to dislike, they snap apart easily and take solder very nicely even with my $12 soldering iron. I tried out my Hakko and a fine tip but it didn’t cut it. Fine tips have quenching problems where the point will not stay hot enough to melt solder and soic parts like I was doing do not really require that tip anyway.Update: these boards let me construct as5600 rotary magnetic position sensor boards small enough to fit my application and I get bare parts from Digikey which have the analog output enabled by default unlike the white boards that are so common. These will just barely sit on the open end of a 1/2 inch pvc pipe.
Ryan M
Reviewed in the United States on November 1, 2022
Used these to solder up a flash SPI chip onto a breakout board to use for prototyping(see bottom left corner of image). The PCB is a quality build and the pads are easy to solder to and can handle a lot of heat. I've used about 6 of these little breakout converters now and have had no problems. Definitely pick these up if you are looking to breakout a SMD IC to connect to a micro or anything else.
Pqrsto
Reviewed in Germany on July 28, 2020
Für Testzwecke baue ich mir gerne vorher die Schaltung auf einem Steckbrett auf. Ich war kurz davor mir den Adapter selbst zu designen, fand dann aber dieses Produkt hier auf Amazon. 6 Stück für 7,73€ - ein wirklich fairer Preis - da spare ich mir den Versand aus China.Die Vorderseite ist für ein 8-pin SOIC Package (small outline integrated circuit; 1,27mm Pinabstand) geeignet, siehe Foto. Die Rückseite habe ich zwar nicht getestet, sollte aber für MSOP und TSSOP passen.
Jordan McBain
Reviewed in the United States on June 30, 2019
These are great. For those complaining this style of PCB isn't for hand soldering and that a heat gun is necessary, I used a magnifying glass, some flux, and a desoldering braid to solder multiple chips in a very short span of time. Search for soldering tips on youtube. I am relatively new to soldering too.
EE
Reviewed in the United States on January 28, 2018
Just what I needed for dealing with SOIC-8 ICs. Good quality, easy to solder.
Michael White
Reviewed in the United States on January 18, 2018
The small chip size really cannot be hand-soldered realistically, and trying was just a frustrating waste of chips. DEFINITELY a heat gun and magnifying glass project if you decide to try. That said, these are nicely-made.
N Elizabeth
Reviewed in the United States on October 12, 2017
These work adequately. Super thin PCB material. Not precut so be prepared get out your utility knife.
Recommended Products
