Your cart is empty.
Your cart is empty. Verify the part fits before purchasing
Steering Bearing Kit for Yamaha
Applications:
BMW F650 GS/GS Dakar 2000 - 2007, F650GS 1999 - 2004, F650GS K72 2009 - 2013, F650GS/M 2003 - 2007, F700GS 2012 - 2016, F800GS 2006 - 2017, G650GS 2008 - 2015, G650X CHALLENGE 2006 - 2007, G650X COUNTRY 2006 - 2008, G650X MOTO 2006 - 2007, HP2 Enduro 2004 - 2006, HP2 MEGAMOTO 2006 - 2008, K1 1989 - 1993, K100 1983 - 1986, K100 LT 1986 - 1991, K100 RS 1984 - 1992, K100 RT 1984 - 1989, K1100LT 1992 - 1997, K1100RS 1992 - 1996, K75 1990 - 1995, K75 C 1985 - 1995, K75 RT 1985 - 1996, K75 RT After 8/1991 1991, K75 RT Before 8/1991 1991, K75 S 1985 - 1995, R100 1978, R100 R 1991 - 1995, R100 RS 1976 - 1992, R100 RT 1978 - 1995, R100 S 1976 - 1980, R100/7 1976 - 1978, R100CS 1980 - 1984, R100GS 1987 - 1994, R100GSPD 1987 - 1995, R100RT Classic 1995 - 1996, R45 1978 - 1985, R45N 1978 - 1985, R45T 1980 - 1985, R45TN 1980 - 1985, R50/5 1969 - 1973, R60/5 1969 - 1973, R60/6 1973 - 1976, R60/7 1976 - 1980, R65 1978 - 1987, R65GS 1987 - 1992, R65LS 1981 - 1985, R65T 1981 - 1985, R75/5 1969 - 1973, R75/6 1974 - 1976, R75/7 1976 - 1980, R80 1977 - 1995, R80 GS 1980 - 1996, R80 RT 1982 - 1995, R80 ST 1980 - 1986, R80/7 1976 - 1984, R80R 1991 - 1994, R90/6 1974 - 1976, R90S 1969 - 1976
Hyosung GT250, GV250
Sherco Enduro 2.5i 2008, Enduro 4.5i 2004 - 2008, Enduro 4.5i Factory Racing 2007, Enduro 5.1i 2007 - 2008, Enduro 5.1i Factory Racing 2007, SE 2.5i-F 2009 - 2013, SE 2.5i-F Racing 2013, SE 2.5i-FR 2011, SE 250 2013, SE 250i-R 2012, SE 3.0i-F 2010 - 2013, SE 3.0i-F Racing 2013, SE 3.0i-FR 2011, SE 300 2013, SE 300i-R 2012, SE 4.5i-F 2009, SE 4.5i-FR 2010 - 2011, SE 450i-R 2012 - 2013, SE 5.1i-F 2009, SE 5.1i-FR 2010 - 2011, SE 510i-R 2012 - 2013, SE F-R 250 2014 - 2018, SE F-R 250 Factory 2016 - 2018, SE F-R 250 Six Days 2018, SE F-R 300 2014 - 2018, SE F-R 300 Factory 2016 - 2018, SE F-R 300 Six Days 2018, SE F-R 450 2015 - 2018, SE F-R 450 Factory 2016 - 2018
Fabio
Reviewed in the United States on July 14, 2024
Buen producto
Luis M.
Reviewed in Mexico on September 12, 2023
R M Wild
Reviewed in Canada on August 25, 2023
Correct size , quality ,good fit and did the job
RWilson
Reviewed in the United States on October 27, 2022
Worked perfect after the stock steering bearings on my F650GS twin became worn and would try to stick in center. This got to the point were it would make it difficult to balance when riding slow.The All Balls Racing bearings were a perfect fit and they come with seals that are far superior to the stock ones that I took off. Remember to pack these with grease before installing them.Tip: Put the races in the freeze for a few hours before you install them. You can also warm up the lower bearing in the oven for a little while. These temperature differences make things easier to install as they temporarily open up tolerances a little.
John - Team Rubicon
Reviewed in the United States on March 19, 2021
Headset bearings are often overlooked and replacing them with the quality set is important I highly recommend this and I'll be using it as a standard replacement and all the bikes I servers
Dan Dubrow
Reviewed in the United States on March 5, 2020
Good replacement bearings and seals
Ken S
Reviewed in the United States on December 29, 2020
These are excellent and so much cheaper than the original BMW parts, I pressed these parts on because one of the the benefits of the All Balls bearings is the uprated seal that keeps the grease in place. Using heat may damage it.For knowing how to remove the old bearings among may other things! Chris R. Harris ... a BMW YouTube sensation has some great videos on all things BMW bikes.I used a Harbor Freight bearing puller to remove the inner from the triple tree,The top inner use a punch in the 2 small holes to knock it out.For the outers the lower is easy with a long drift to knock it out.The top outer is more difficult, you need to use the small gap between the bearing and the frame, I put a flat screwdriver in the groove from the top and set a 1" dowel from the bottom and hammered it on all sides and effectively walked it out! I hope this helps!
Recommended Products
