Shopping Cart

Your cart is empty.

Your cart is empty.

AN8 Feed Fuel Line Kit for Holley 4150,7/8'Carburetor Dual Feed Fuel LineW/Silver Psi Gauge for Holley

4.7 (9) Write Review
Free shipping on orders over $29.99

$32.99

$ 16 .99 $16.99

In Stock

1.Color:6 An


About this item

  • 【Apply to】Fit for any 4150 Based Carb, compatible with Holley Quick Fuel AED and more
  • 【Premium Material】: Made of lightweight aluminum. The black anodized surface for enhance its oxidizing, rusting and corrosion resistance. The Hose is stainless steel braided. Adjustable 0-160 PSI Gauge
  • 【Thread Size】Perfect for Holley 4150 Style Carburetors with 7/8" - 20 Fuel Bowl Fitting and comes complete with stanchions to attach them to the carburetor! Designed for a great fit on Holley Carbs with a 9-5/16" Center to Center. This fuel log has a 3/8" NPT Female Inlet Fitting, 1/8" NPT fitting in the rear and another 1/8" NPT fitting near the front for a fuel pressure gauge
  • 【Mateial】The fuel line kit consists of aluminum black anodized part and stainless steel braided hose.The pre-assembled fuel lines clean up your engine compartment and properly deliver fuel to your carburetor. Deliver the right amount of fuel at the correct rate to power your performance ride on the strip or street
  • 【Easy to Install】: Package comes with a pre-assembled braided stainless steel carburetor dual line kit, so easy to install. Notice: If the hose ends leaked, it is recommended to use a lace or tape to seal it.If the length size is not suitable, you can DIY trim


Product Description

2
2

Santos
Reviewed in the United States on April 15, 2025
no leaks.., well made product
Diego Covarrubias
Reviewed in Mexico on August 9, 2024
Está muy larga la manguera
Eric The Tire Guy
Reviewed in the United States on January 31, 2024
I got this to use on a Holley 4150 carb. It’s slightly (1/2”) too long. Set up on the workbench the carb connectors are 10” center to center. The carburetor inlets on the Holley are slightly less than 9.5” center to center. The line is flexible enough that it could work, but it would have a bow in it so I decided to just use the old one I have for now. Disappointing. I don’t know if the spacing is different on something like a Demon carb, or if you swap out for the billet metering blocks, but since I see someone else posting that it’s too short, I think perhaps there’s and inconsistency in the assembly process
Aliviana York 2.0
Reviewed in the United States on January 28, 2024
The kit comes with the center hose assembled with the fittings, but you may need to shorten the hose depending upon your carburetor. It's nearly 10 inches long from bowl fitting to bowl fitting.The included gauge is not really good for carburetor use, it reads 0-160 psi which is too much range, that's EFI pressures. It's glycerine liquid filled but the air bubble is a bit large, it's just not a high quality gauge.There's a pipe plug to block off the gauge port included too.The AN fittings and hose seem to be good quality.I would recommend this kit to someone who doesn't expect a simple bolt on kit right out of the box, and who has thier own low pressure gauge.I Hope My Review And Pictures Were Helpful To You!!
Joseph Trimarchi
Reviewed in the United States on January 12, 2024
Great product fast delivery Great price
Customer
Reviewed in the United States on September 13, 2023
Product has metric fittings which will not go all the way into Holley bowlsThe outer diameter is to big
Arturo
Reviewed in the United States on November 6, 2023
Does not fit, to short, can’t use. Waste.
Michael Macri
Reviewed in the United States on November 3, 2023
Happy with the purchase
Larry
Reviewed in the United States on November 20, 2023
Very happy with everything!