Your cart is empty.
Your cart is empty. The Active PoE Splitter splits a PoE signal into an 12VDC power and 10/100Mbps ethernet data source.
This device allows you to run ethernet cables from a PoE Switch over long distance, and then split the PoE signal into a separate data signal and 12Vdc power sources in order to run an non-PoE devices.
Specifications:
Input: 44-54V DC; Shielded RJ-45 female;
Output: 12VDC max 1.5A 18W; RJ-45 male
DC jack 5.5*2.1mm
Length of DC power cable: 10cm
Operating Ambient Temperature: -10 to 45℃
Regulatory IEEE 802.3af
What is included:
4 x 12v PoE splitter
Mr FHO
Reviewed in France on January 12, 2025
Mais je verrais comment il se comporte avec un routeur 4G de 1A a son extrémité, on verra comment il absorbe les pic d'intensité très connus sur ce genre de matériel...
Ryley lego
Reviewed in Canada on November 19, 2023
Bought these because I have outdoor camaras that are not poe and got tired of having extra power bricks around to power them when I already have a poe switch here.I've installed them and they have been working great
Charles M
Reviewed in the United States on November 7, 2021
I’ve purchased this 4 pack 3 times for use on 6 cameras. They work, easy to connect, but don’t last. They burn out about every 6 months. Looking for another brand that’s more reliable.I recently opened up 2 of the failed units. In each one the R15 resistor is burned.
raw-8k
Reviewed in Japan on September 14, 2020
監視カメラをPOE対応にする便利グッズ、これはおすすめ。
wetcoast79
Reviewed in the United States on August 27, 2020
These worked as described initially but I started seeing intermittent signal drops that increased in frequency over time. I had a deployed three of these and had one unused. I finally climbed the pole to troubleshoot and the three were flashing every couple seconds or so. I replaced each one with the unused one and they worked with that one and the lights stayed on continuously with the new splitter. The three others had failed. They were mounted in a waterproof box. Don't recommend these for that reason.
C. Williams
Reviewed in the United States on June 15, 2019
These are great adapters, makes getting power to cameras and lights very easy.One note is that I tried to run a big PTZ camera and it could not keep it powered solidly, but the camera's default power brick was a 12vdc/3amp and though I didn't do the math, I think either this adapter or my TRENDnet PoE switch just couldn't do it.To be fair, it could be my switch, but I am using these to power to Amcrest bullet cameras and power a secondary IR flood and have had no issues.As I expand, I will be buying more of these!
Solomon
Reviewed in the United States on May 3, 2019
Nothing much to say, it works well!
dany
Reviewed in Canada on April 5, 2019
Received my poe splitters for my ip cameras. Very easy to install and connect to my poe switch. 1 of the 4, I received was defective. I advise Anvision and within a couple of hours they replied and accept to send another one.Already received the replacement one. Works perfectly. Thank you Anvision for the excellent service.
Alertus Technologies
Reviewed in the United States on November 12, 2018
We've used this device extensively in a low voltage application. It is reliable and easy to use. 5 stars
Rick D. Fryar
Reviewed in the United States on September 17, 2017
Easy plug and play POE 802.3af compliant power for my IP Cameras. Each one is using about 3 watts from my switch, so not too large of a draw. Will order more once I get some more cameras.
C. Beytas
Reviewed in Canada on December 10, 2017
100% China made. Not sure these are fully IEEE 802.3af compliant but they work.At 10 Watts these things run very hot with a smell of melting plastic.I'm using them to power a raspberry pi (below 5W) and they're fine.UPDATE: It is now 4 years later and all four of these adapters have failed. The first one died after 2 years and the fourth one just last month.
Someone
Reviewed in the United States on October 4, 2017
Several problems I identified:1. Does not handle large current increase during start up (smaller than its rated capacity of 1.5 A)2. Does not handle large current swings (I tested from 0.75 A to 0.0 A consumption, the LED went off)3. There are two board revisions, one with a bigger inductor and capacitor. They seller is shipping both. The problems above were identified in the "better" board, it's likely that the other one also suffers from the same issuesIt might work for low wattage stuff, but it's just not good if you try to use it close to its rated capabilities.
MarathonJon
Reviewed in the United States on November 28, 2016
worked as described
Recommended Products
