Shopping Cart

Your cart is empty.

Your cart is empty.

AURSINC TinySA Ultra+ ZS406 Spectrum Analyzer with 50W Attenuator, 2025 Upgraded 100kHz-5.4GHz V0.4.6 Portable Frequency Analyzer with 32Gb Card, 2-in-1 Signal Generator 100kHz to 900MHz Input

Free shipping on orders over $29.99

$33.99

$ 17 .99 $17.99

In Stock

1.Model:Tinysa Ultra+ Zs406


  • [50dB Fixed Attenuator Spec] Rated to 50 Watts, DC to 3 GHz, N Female to N Male Directional. Attenuation: 50 dB ± 2.5 dB, Impedance: 50 Ω; VSWR and Attenuation Accuracy: 1.20:1 Max. Connector: N(M) Input N(F) Output. Black Anodized Aluminum Heatsink Body
  • [Upgraded TinySA Ultra] Produced by Hugen, AURSINC Tinysa ULTRA+ zs406 owns high performance frequency in 100khz to 900MHz, and when in ultra mode, the analyzer can reach 5.4GHz. With new 4'' touchscreen display and installed with the latest hardware system V0.4.6. Built-in 32Gb micro SD card for data transfer and storage
  • [Frequency Range] Tiny sa ultra measures from 100KHz-5.4GHz: Spectrum Analyzer for 0.1MHz-900MHz, with Ultra mode enabled, level calibrated up to 6GHz, can observe signals up to 12GHz. Switchable resolution bandpass filters from 200Hz-850kHz, you can fast and accurate execute measurement tests. Color display showing max 450 points providing gapless covering up to the full frequency range
  • [2 in 1 Device] When not used as Spectrum Analyzer it can be used as Signal Generator, MF/HF/VHF sinus output between 100kHZ-900MHz, UHF square wave output between 800mHz-4.4GHz, Mixing signal output is between 4.4GHz-5.4GHz. Built-in calibration signal generator that is used for automatic self test and low inputcalibration
  • [PC CONTROL] This tinysa ultra can connect to a PC via USB, Tinysa-APP directly transfers data to the computer. The USB interface implements the Serial over USB (CDC) protocol and there is a large set of commands that can be invoked over the serial interface. These command can be used to perform measurements or update internal settings. The driver for Windows will install automatically after connecting to a Windows PC. The driver for Linux is built into the kernel
  • [200Hz-850kHz RBW] RBW frequency from 200hz to 850khz which can be set to match the measurement requirements, meet SBB two-tone test requirements and fast scanning. The RBW is as low as 200Hz, which can effectively distinguish adjacent signals and meet the requirements of SSB dual-satellite inter-modulation test. Input Step attenuator from 0dB to 31dB (can not be used not in combination with LNA)
  • [What You Get] 1x Tinysa ULTRA+ zs406 Spectrum Analyzer(4inch touchscreen, 5000mah rechargeable battery); 1x 50W Attenuator; 2x 30cm ALSR100 SMA cables; 1 x USB Type-C data cable; 1x SMA-SMA barrel connector; 1x TLanyard and touch plectrum; 1x Antenna with SMA connector; 1x 32GB MicroSD card(plugged in the host), 1x Stylus Pen



Product Description

2025 Upgraded Tinysa Ultra+ ZS406 Spectrum Analyzer with 50W Attenuator kit for QRP Radio Test

tinysa ultra+ ZS406 spectrum analyzer

AURSINC Tinysa ULTRA+ ZS406 has high performance frequency from 100khz to 900MHz. In ultra mode, can reach 5.4GHz. With 4.0 inch sensitive touchscreen display, more professional, stable, sensitive and easy to be operated. For more information please visit below link: tinysa.org/ultra/

Features: Added DC-3GHz 50W Coaxial Fixed Attenuator. Tinysa ultra can be used to test a DIY QRP radio which can test a maximum 50w radio

TINYSA ultra+ zs406

Spectrum Analyzer & Signal Generator in ONE, 2-in-1 Signal Generator 100kHz to 800MHz MF/HF/VHF UHF Input

TINYSA ULTRA+ ZS406

Best Performance Settings

The TinySA Ultra+ ZS406 has many setings. In general one should NOT make changes to settings that are not fully understood. In the ultra mode a number of settings MUST be in AUTO mode (indicated with the letter 'A' inside the checkbox)

  • SPUR REMOVAL
  • IF FREQ
  • MIXER DRIVE
  • SCAN SPEED
  • BELOW IF
  • HARMONIC must be set to '3'

In case of doubt reset to factory setting using PRESET/STORE/FACTORY DEFAULTS and PRESET/LOAD STARTUP

Note: The DISPLAY/SWEEP SETTINGS/FAST mode does not work as intended. Avoid using this mode. Do not change the AGC and LNA setting in the expert config menu

TINYSA ULTRA

Powerful FULL featured Spectrum Analyzer

  • The RBW is as low as 200Hz, which can effectively distinguish adjacent signals and meet the requirements of SSB dual-satellite inter-modulation test
  • Input Step attenuator from 0dB to 31dB (can not be used not in combination with LNA)

tinysa ultra

Built-in 32Gb micro SD card

  • Built-in 32Gb micro SD card for data transfer and storage. With its wide range of trace and analytic functions, you can save settings, traces, and screen shots
  • Audio Out, standard 3.5mm headphone jack, put on the headphone or connect to the amplifier if needed

tinysa ultra+ ZS406 spectrum analyzer

Built-in 5000mah rechargeable battery

  • Built-in 5000mah rechargeable lithium battery, can work continuously for more than 3 hours, with type-C charging cable and LED charging indicator
  • It can be fully charged within 3 hours, has an long battery life, without the need for frequent charging
TINYSA

Specification Differences between TinySA ULTRA and Tinysa ULTRA+ ZS406

tinysa ultra+ spectrum analyzer

Douglas
Reviewed in the United States on May 25, 2025
Great little Spectrum Analyzer!! Works as advertised.
R. Johnson
Reviewed in the United States on May 21, 2025
this Spectrum analyzer works great and even has a waterfall mode. if you have a radio that doesn’t have these features you really need this. i can spot frequencies being used in one glance to see where people are operating.
R Paq
Reviewed in the United States on May 18, 2025
Great quality product. A great tool for the Amateur hobbiest.
Pike City
Reviewed in the United States on March 23, 2025
Just wanted to say that it's amazing what can be packed into such a small device! Back in the early 1990's I used to use large IFR test rigs to do what this device does. Consider: those IRF rigs used to cost $15K/unit and this is less then $200, well, that's a lot of bang-for-the-buck!The AURSINC TinySA Ultra+ ZS406 Spectrum Analyzer is fun to use and work with. This kit includes a helpful 50W Attenuator, too. So cool!5/5 stars for great engineering and programming!
CJ
Reviewed in the United States on January 20, 2025
The TinySA Ultra+ represents a significant upgrade from its predecessors, offering impressive functionality in a portable package. The 4-inch display provides excellent visibility of spectral data, with responsive touch controls and intuitive menu navigation. The frequency range from 100kHz to 5.4GHz covers most common applications, making it versatile for RF development and troubleshooting.The integrated signal generator function up to 900MHz is a valuable addition, effectively making this a 2-in-1 tool that reduces the need for separate test equipment. The hardware version 0.4.6 brings welcome stability improvements, though occasional software updates are still recommended for optimal performance. The included 32GB card provides ample storage for captures and sweeps.Performance-wise, the sensitivity and dynamic range are surprisingly good for the price point. The noise floor is manageable, and the frequency accuracy is reliable enough for most hobbyist and professional applications. The battery life is decent, lasting several hours of continuous use, though it's worth noting that intensive scanning can drain it faster.One minor consideration is the learning curve - while the interface is well-designed, newcomers to RF analysis should expect some time to become proficient. The documentation could be more comprehensive, but the active user community helps fill any knowledge gaps. For anyone working with RF systems, amateur radio, or wireless development, this analyzer offers exceptional value, providing professional-grade features in an accessible, portable format.​​​​​​​​​​​​​​​​
Paul
Reviewed in the United States on April 8, 2025
The TinySA is exactly what was described. Took it out of the box and made some simple measurements right then. I have their nano VNA too. Like them both. Aursinc has done a great job with these instruments. I’ve upgraded the nanoVNA several times with no problems. I did work in IT with mostly machine control stuff so your ease of doing those upgrades may be different but you can just use them the way the come. Lots of YouTube videos on what to do with them and how. Buy some attenuators so you don’t fry the thing with to strong a signal. Amazon has them too.
Richard Hartley
Reviewed in the United States on April 7, 2025
Incredibly advanced technology in a small package! Helped me locate the source of RFI that was interfering with my 25 year old garage door opener (LOL - it was my Bitcoin miners), but this will also be quite useful as I'm a ham radio operator SWL fan and IT networking tech, it's so versatile it will even see wifi6 and 7 frequencies. You can link it to a PC also however there are no drivers (yet) for Windows 11, only 10 and earlier. Not an issue as I run 11, 10, 7, XP, Linux and Mac at my house. Heartfelt thanks to the developers from this old fart tech geek! Love it!
Nick
Reviewed in the United States on April 7, 2025
The product is an excellent tool, but the first one Amazon sent me was a defective item that had been returned. The "Ultra" mode was already unlocked, and the unit would not pass self-test. The replacement item was perfect!