Your cart is empty.
Your cart is empty.Product Description
Before Repair & After Repair:
Car Dent Puller with Bridge are ideal car dent removal,door dings and hail damage repair,minor dent removal.The dent remover kit great to work for the sheet metal processing of truck,automobile, refrigerator,motorcycle body, washing machine and other metal surface dents
-
FIRST Method of USE
1. For small dent and soft surface (Not suitable for metal surfaces exceeding 1mm.)
-
SECOND Method of USE
2. For deep dent (But can't exceed 20mm depth.)
-
Bridge Dent Puller
Different size of tabs, can repair different size of the dent, Suit for dent size within 14cm.
-
20W Glue Gun
Quick Heating System: 3-5 minutes after the pre-heating.
-
Step 1
Clean dent surface, put glue sticks to gun & heat, connect power source and preheat for 5-10 minutes
-
Step 2
According to the dent size to Choose the suitable glue Puller tab
-
Step 3
Use bridge dent puller to align and press the puller to pull up the dent, until the dent disappear.
-
Step 4
After finishing dent,use the alcohol or hot water to clean the glue which on the car and puller tabs
-
Step 5
Remove the glue from the car with a spatula.
Packing List:
1× Double Pole Bridge Dent Puller
5× Black Glue Puller Tabs
5× Blue Glue Puller Tabs
2× Glue Shovel + 1× Empty Alcohol Bottle
1× Black Clean Cloth + 1× Instructions Card
jimmy
Reviewed in Canada on February 21, 2024
There is not to much difference after I use this tool because the glue is not strong enough to support it when I pulled it with the tool.
Customer
Reviewed in Canada on January 25, 2024
OK for the price
John Oughton
Reviewed in Canada on December 8, 2023
I used it to pull one small dent and parts of a larger one.
Michel
Reviewed in Canada on July 17, 2022
N’as pas donné de bon résultat pour ma bosse car la bosse est situé sur le rebord de du contour de l’aile ! Utilisation unique des adapteurs car la colle ne s’enlève pas sur les adapteurs ! Parfait pour petite bosse seulement !
Rajat Kumar
Reviewed in Canada on January 9, 2021
This product is amazing it really works. The main thing is boil the water close to boiling point and then put the water to the place where you want to work on dent (where the temperature is too cold). Then try the glue technique and it will stick for sure and dent will be pulled...Only issue is you will run out of glue sticks and It would be awesome if someone can link me the glue sticks only without the glue gun since I already have it in the package
MARK MCFADDEN
Reviewed in the United States on September 17, 2020
I received the tool and started using it on my car. The tool was able to apply enough safe leverage against the door to pull some dents out. It is very easy to align with the glue tabs and position the feet in the proper position.However, I feel as if the handle is not very comfortable to use. It is smaller and with trying to pull some dents you have to apply a lot of torque to pull the tabs. I feel if the handle were larger and more like a handle it would be easier to turn, in addition, it would provide a handle to be able to additionally pull and tug on the tab as well.The other issue I found is that the tool has a tendency to twist when applying pressure. This twisting motion changes the angle with the tab and seems to cause the tool to slip off of the tab frequently. I found myself constantly having to reset the tool. Then trying my best to prevent it from twisting.The scrapers provided with the tool are not all that helpful with getting the glue off of the surface. However, this could have more to do with the glue used. I think I am going to try to heat the glue up slightly and then try using the tools again.Overall, the tool is exactly as described and does work. With me, I just feel there is some room for improvement. For the work it does, as is, it is worth the money and does help.Mark
Adam Shin
Reviewed in the United States on June 2, 2020
So to start this review off, I'm an idiot. I swung my door open at a gas station and hit it against a safety pillar next to the pump. After hating myself for a couple days, I got a quote from a paintless dent repair company in my area. $225! I mean, take a look at the picture. That doesn't look like 225 dollars worth of damage to me. I decided to buy a dent puller from Amazon and picked this one.PROS:- Cost | I felt like the other, more expensive dent pullers were essentially the same thing as this one.- Puller Heads | It comes with a lot of heads depending on the size of your dent(s). I do wish there was one size smaller, though.- It Works | I mean, it does its job. The effectiveness may depend on your dents specifically, but it definitely works.CONS:- Spring | For some reason, the spring on my unit is slightly crooked. I'm not sure if I got a bad spring or if the design kind of forces it into that position, but it can make the apparatus awkward to use.- Puller Heads | As stated above, I wish it came with one size smaller. This is dependent on your dents though.- No Hot Glue Gun Included | This is not as big of a deal, as most other pullers don't come with a gun either. It just would have been nice. Not a huge deal; I just had to buy one separately.- Pivot During Use | The "feet" on this thing are ball and socket, so they tend to pivot a lot. I understand this is part of the design, as the contour of your car is never flat. However, you have to be really careful where you place the feet. If you don't, it'll pull the head off at an angle (which could cause it to not pull the dent at all).Take a look at my before and after pictures. I think the after picture doesn't accurately show how it looks now, as I think it's more noticeable in real life. However, it's not really noticeable unless you're looking for it. It is a huge improvement, and for
Customer
Reviewed in the United States on June 20, 2019
This thing flexes and turns so much your not pulling straight up on the dent. the glue is miserable to get off had to buy goo remover. If there is any type of ridgearound the dent your going to have to buy finesing tools to knock the ridge down. There advertising says DENT PULLER yes it is a dent puller but nowhere does it say it will pull it out all the way because they know it just might not.had to also tighten up the ends of it with a wrench. I had 6 dents to pull still have 5 the best result i got was with a 2.5 in suction cup. live and learn. this is a good idea in general but not with this item. ......... UPDATE the first day you posted my review it it was on buried on page 6 or 7th page i did not give you a good review at all it's just the way it goes so can somebody tell me why this happens while GLOWING reviews from 2018 still on the first page is it Manelord that controls this or is it AMAZON? i'M NOT ABOVE ASKING THE FEDERAL TRADE COMMISHTION to look into it answer please!
Neil in MA
Reviewed in the United States on May 29, 2019
I must admit to being a bit skeptical about this and other similar products. The Youtube videos made it look so easy, how could they all be fake. Well, they're not.My '13 Subaru is in excellent condition, except of course for the myriad parking-lot dings that other less considerate persons inflicted on my car. Nothing deep, but quite visible. Really annoying (don't get me started!)This product does not include a hot-glue gun, which in my case is just fine since I already own one. Following the simple illustrated directions I applied a dab of ordinary hot glue to the tip of the smallest foot, pressed it gently onto one of the dings and waited a minute or so for the glue to cool. Then using the nicely designed puller, turned the screw and -POP- off comes the foot, taking with it most of the glue.Absolutely amazing, the ding was gone after just one application. I felt like I'd just witnessed a little bit of mighty-fine-magic.Then moving on to the half-dozen or so other similar dings they disappeared one-by-one. I then cleaned off any remaining residue with the provided spatula, then a quick rub with alcohol and reapplied paste wax.I can't praise this product highly enough. I particularly appreciate the fact that the load bearing parts are all made of durable steel, this puppy is NOT going to break.Thanks and thanks again. You saved me aggravation and (if I had bothered) lots of expense having a body shop take care of this. Nicely done!
Recommended Products