Shopping Cart

Your cart is empty.

Your cart is empty.

Beduan Extended Tank Drain Assembly Kit with 1/4' NPT Elbow Push to connect fitting 20 Inch Nylon tubing 10mm OD barb brass ball valve for Air Compressor

4.5 (8) Write Review
Free shipping on orders over $29.99

$15.99

$ 7 .99 $7.99

In Stock

1.Style:250psi


About this item

  • The valve kit comes with one 20 inch long 1/2" OD nylon tube,Easy and fast installation.Max working pressure:464.1Psi.Burst pressure:826.7Psi.Work temperature:-40~248℉
  • The extended tank drain kit offers nickel plated copper elbow fitting.Size:1/2" Tube OD x 1/4" NPT Male Thread.Maximum working pressure:853.4Psi.Work temperature:-22℉-230℉
  • High temperature and high pressure resistance of brass ball valve.Size:Double 10mm OD barb.Maximum working pressure:250Psi.Work temperature:-22℉-230℉
  • Add an extra Hex bushing brass adapter.Can be used to connect copper nickel elbow to fit various air tank joints.Size:1/4" NPT Female x 3/8" NPT Male.
  • An additional seal tape and hose clamp will be provided to ensure installation reliability and to prevent leakage


Product Description

Extended Tank Drain Assembly Kit

Beduan, manufacturer & distributor of top pneumatic supplies Our production line includes:

  • Compressor Filter and Regulator
  • Push to Connect Fittings
  • Solenoid Valves
  • Compressed Ferrule Fittings
  • Marginal products
  • Visit the beduan Store and choose what you want

Beduan Extended Tank Drain Assembly Kit

250Psi

  • Maximum working pressure:250 Psi
  • Hose Length:20 inch
  • Max Temperature:230℉
  • Air Inlet: 1/4” NPT Male Thread(With 3/8" NPT Male Thread Adaptor)

ball valve

Brass Ball valve

Size:Double 10mm OD

Max working pressure:250Psi

Work temperature:-22℉-230℉

nylon tubing

Pressure resistant nylon Hose

  • 20 inch long 1/2" OD nylon tube,Easy and fast installation
  • Max working pressure:464.1Psi
  • Burst pressure:826.7Psi
  • Work temperature:-40~248℉

eblow fitting

High Quality Elbow Fitting

  • Size:1/2" Tube OD x 1/4" NPT Male Thread
  • Maximum working pressure:853.4Psi
  • Work temperature:-22~230℉

accessoriy

accessories

  • one brass Hex bushing adapter.Size:1/4" NPT Female x 3/8" NPT Male
  • One hose clamp
  • One Teflon tape

Note:

1.Before installation,the thread of fitting needs to be wrapped with seal tape to avoid leakage.

2.When the pipe is installed to the quick connector, it can be rotated several times to ensure that the tube is installed into the sealing ring, otherwise leakage will occur.

3.We provide one 20 inch long nylon tube,you can cut according to your own needs.Pay attention to ensure that the section is smooth and vertical.To avoid leakage after installation.

4.After installing the ball valve,do not forget to use the hose clamp, otherwise leakage may occur.

5.The Kit has passed the test before leaving the factory and fully meets the performance requirements.

6.Don't try to use beyond the pressure limit!

Reasons to buy our products:

1.The product is made up of several parts, which can be used as Tank Drain Valve Kit.Of course, each accessory can also be used separately.

2.It's easy to replace parts. All parts can be purchased separately.Don't need to buy a whole set of products again, waste unnecessary cost.


Levi Cates
Reviewed in the United States on March 16, 2025
Junk not worth buying
Big Twin
Reviewed in the United States on March 11, 2025
Easier to drain tank with extension.
Rick Gebo
Reviewed in the United States on March 1, 2025
No matter how much you seal this to tank, it still leaks
Murphy
Reviewed in the United States on August 19, 2024
Would have been nicer if hose was a foot longer.
Jeff P.
Reviewed in the United States on October 6, 2024
Put this on my 20 gallon air compressor to blow the water out of the tank it works
Brook Simons
Reviewed in the United States on January 9, 2024
Was easy to install and works very well.
Phils2888
Reviewed in the United States on January 2, 2023
I just installed this and so far I am happy with it. It is a little on the cheaply made side but so far does the job it was intended to do. Would have been nicer to have been a better quality hose like braided and not a generic hose clamp. So nice not to have to get down on your knees and blindly reach under the tank with a pair of pliers to bleed the tank. Now I bleed the tank every night and have a drier air supply. We’ll worth the rather cheap investment.
Mr. Optimistic
Reviewed in the United States on December 3, 2022
I wish I would have gotten this sooner, makes draining the tank so much cleaner and easier. Seems to be working great so far. I know I probably could make one myself, but buying the individual pieces probably costs more than this did.