Shopping Cart

Your cart is empty.

Your cart is empty.

Brake and Clutch Fluid Pneumatic Vacuum Bleeder Bleeding Tool Kit to Change Brake Clutch Oil Power Steering Oil Engine Oil for Auto Car Truck Motorcycle Use

Free shipping on orders over $29.99

$21.99

$ 11 .99 $11.99

In Stock
  • This brake clutch oil change tool is good at exchanging brake clutch fluid, power steering oil, engine oil and any other fluid. Use 90-100PSI shop air to form negative pressure in the brake system, sucks out waste oil and air, and guide the new oil to fill all the system.
  • Pour the new brake oil into the master cylinder, connect the black cone nipple to the brake bleeder valve, connect the compressor to the 1/4" air quick plug. Open the air compressor, wait a few mins until clean fluid comes out without bubbles, close the air compressor and turn to the next brake, until changing the brake oil for all the wheels, check the pressure of the pedal.
  • One man operated brake fluid replacement tool, easy and simple. You do not need to press the pedal back and forth, or need other's help, and you will not stain the floor too. Please note, you need to seal the drain screw on the bottom of the collection bottle by Teflon tape, and during the bleeding one by one, you need keep filling new fluid into reservoir to avoid it from empty and air leaks in.
  • YSTOOL brake oil extractor kit has a 340ml waste oil collection bottle, a lid assembly with ball valve, 1/4" NPT European style air quick plug and a 80" long hose. There are a elbow black rubber cone suction nipple and a dark green plastic cone nipple for you to choose. This pneumatic bleeder tool is widely suitable for most vehicles, such as sedan, motorcycle, truck, SUV, etc.
  • Convenient pneumatic brake bleeding tool, save you from sitting there to manually pump by hand pump or press the pedal back and forth by traditional bleeding method.



Product Description

114
bleeder
bleeder
nipples
ball
use

Specification

1. Material: PE, silicone and metal

2. Bottle capacity: 340ml

3. The length of hose: 80" long

4. Air inlet: 1/4" NPT European air quick plug

5. 2 suction nipples: a elbow black rubber cone nipple and a dark green plastic cone nipple

6. Max. pressure: 100psi shop air

Easy to Bleed the Brake Fluid

1. Make sure vehicles master cylinder reservoir is full

2. Bleed the system in the following order:

a. Master cylinder (If bleeder equipped)

b. Wheel cylinders and calipers in succession, beginning with the wheel closest to the master cylinder and progressing to the one farthest from it

3. Assemble the brake clutch fluid bleeder tool and seal the drain screw on the bottom of the collection bottle by Teflon tape.

4. Connect the shop air to the waste oil collection bottle, and connect the black cone nipple to the brake bleed valve. Open the ball valve.

5. Open the vehicle’s brake bleeding fitting 1/4-1/2 turn and allow the fluid to flow into the storage jar

6. Fill the master cylinder reservoir back to normal with fresh fluid and proceed to the vehicle’s next brake and perform the same steps as above, until changing the brake oil for all the wheels

7. Check the pressure of the pedal


Jesse Spolerich
Reviewed in the United States on September 7, 2024
Easy to hook up and easy to use. I used this to ensure there was no air in my clutch line before installing in my Civic. After install there was no need to bleed the system which was my goal, there is not a lot of room. An air compressor is needed to create the suction. Drainage is easy as well. My only issue is the hanging hook, due to the weight of the air line connector it is top heavy and hangs diagonally. I also used it to bleed the brakes on my daughter's car, again it worked great. I do recommend this if bleeding brakes or a clutch is in your future.
saejin park
Reviewed in the United States on May 21, 2024
It works as designed and is a good price.In addition, I have to emphasize that YSTool's customer service is second to none.I will keep purchasing YSTool's products.
Pistol Pete
Reviewed in the United States on October 25, 2024
The media could not be loaded.
Timothy Watkins
Reviewed in the United States on October 8, 2023
I've used this on 2 vehicles and 3 motorcycles so far. Saved me so much money by flushing brake system myself. Best of all. It is a 1 person job!!!! No screaming at your kid to hold the brake to the floor while they cry about their leg cramping up.
Mikeinnyc
Reviewed in the United States on October 15, 2022
I was honestly praying that this was going to work because doing a brake job is horrible. I replaced all my brake lines my brake hoses my brake calipers my discs and my drums. I was hoping the final part would be easy but as usual I got a 2x4 to the Head. This didn't work maybe it works for you but it didn't work for me
Matthew S.
Reviewed in the United States on June 5, 2021
Works pretty well, but you have to test it without the canister and adjust the airflow to find max vacuum because wide open it pulls no vacuum.
Mark
Reviewed in the United States on May 24, 2021
This tool turns a job I used to hate into one to look forward too . the tool works perfectly as one would expect. I do have one complaint. The air connector is of a type that I didn't have so be aware that a trip to the auto parts store will probably be in order. I have several air chuck types and non of them fit properly. I read other reviews and disagree with the statement made by one reviewer that your compressor needs to to have a vacuum port. This tool works on the a venturi principle and creates it's own vacuum. Great tool for the job of changing brake fluid or bleeding your brakes using only one person.
BMR
Reviewed in the United States on April 23, 2021
had to buy a different fitting for it & after I got the right fitting it never had suction. On a big compressor or little did not matter. Ended up bleeding the clutch by hand. Useless do not buy.
Recommended Products