Zhen
Reviewed in the United States on January 11, 2025
Purchased it for under $130 including shipping through an Amazon resale item.For that price and the fact that it is solid wood, it seemed like a good value. There were some blemishes despite the listing indicating like new/ very good, but given the price, just accepted it as is.However had to cut the back of the vanity in order to accommodate pipes for plumbing. Measure out the correct size, then use a oscillating tool or jigsaw to cut it. Use some white chalk to cover up blemishes.Also the holes for the door handles did not come pre-drilled on both sides, only one side, had to self-drill a new hole which cracked the wood slightly, but the handle covered it up.
Jacob Gilbert
Reviewed in the United States on March 29, 2024
I want to start by saying I am not a carpenter, nor do I do any woodworking. I'm an average DIYer that does their own work to put the highest quality products in my home at less cost.The Good:- High quality- Solid hardwood cabinet face- Solid 1/2 cabinet WITH a full plywood back- Coating is flawless with a waterproof material- Easy Assembly with good directionsAssembly.- Soft Close door hinges INCLUDEDThe Bad:- Amazon Delivery means potential shipping damage- Plywood by nature can come warped (chip board is manufactured and pressed together with glue which means it almost always comes flat, but is VERY susceptible to water damage)- Assembly may cause small problems aligning if grooves aren't perfect. Offsetting slightly fixes this.Summary:I would highly recommend these. I bought two, one for each of my bathrooms. The finish is very durable and they are made entirely of 1/2 plywood, NOT the particle board junk at thr box stores that cost twice as much.The value to dollar ratio is absolutely amazing on these. The style is stunning, an equivalent from the box stores would have cost hundreds more and been junk.Assembly REQUIRES wood glue. I recommend titebond III since it's waterproof and will hold up better in a bathrooms humidity.The screws it comes with are to hold the cabinet together while the wood glue dries. The glue is the main securing method of the panels so be generous and wipe of excess immediately.Definitely purchase some 1/2 pipe and pipe clamps. Apply the glue first, then clamp the cabinet together. THEN secure with screws.One of my cabinets sides did come somewhat warped which is why I gave this 4 stars. Since I'm on a timeline to get it installed I didn't call the company but I'm sure they would have sent me a new panel if asked.To fix the panel I used pipe clamps to hold the Plywood bent in place. After a day or so it should be fine. I did this part while thr glue was drying.All and all these are great cabinets that anyone can assemble if you take your time and use common sense. Don't bash a company for your own lack of knowledge in assembly.
mry russo
Reviewed in the United States on November 5, 2024
Extremely difficult to even try to assemble. NO instructions NO IDEA which item goes first. NO video for this item. No glue, no tools. Package slip incorrectNever will I purchase from here again
thejosh
Reviewed in the United States on March 14, 2023
They did a great job cutting corners in the right places to keep the price down. The whole thing is thin plywood (which is good for a bathroom - much better than particleboard), except for the front, which is solid wood. The front feels premium. The doors have good weight to them and the soft close is a great touch!The issues I had:1) You may need extra tools (see other issues). The extra tools I needed: (2) 36" clamps, drill bits2) One of the panels was curved (see pictures). This wasn't a big deal since I had clamps - I applied lots of wood glue to the track, used two clamps to hold the curved piece straight, then installed the screws as instructed. After a few hours, I took the clamps off with no problem!3) The predrilled holes were often not aligned. Not a big deal. I just had to add about 10 holes, myself.4) The directions are not great. This is really only a problem in 1 area: They first have you glue/screw in the side panels. The following step has you install the back and the bottom. BE VERY CAREFUL in this step to put in both panels at the same time as the side panels!!!!!!!!!! In order to get the bottom and back to fit together, you need to slightly lift the side panels up out of their tracks to make room for the back panel to fit in. If you wait for the glue on the side panels to dry first before adding the back and bottom, you will be in trouble!Overall, great product - minus 1 star for the curved panel and the bad instructions.