Your cart is empty.
Your cart is empty.EZ-SET TORSION SPRINGS The EZ-SET Torsion Spring System makes torsion spring installation faster and easier for the do-it-yourselfer. Our system eliminates the difficult and manual winding process. EZ-SET TORSION SPRING HOW TO REMOVE TENSION FROM REMAINING SPRINGS IN ORDER TO WEIGH DOOR These instructions apply only for the purpose of removing tension from residential EZ-SET torsion spring configurations with standard radius (springs mounted to the front header of the garage). If the door has two EZ-SET torsion springs and only one is broken, always replace both springs. TOOLS NEEDED:3/8" medium-duty reversible drill 1/4" insert bit or 7/16" socket wrench C-clamp or locking pliersSTEP 1: Disconnect the garage door opener, lock the door securely in the DOWN position using the door lock, C-clamp or locking pliers placed directly above a roller. This must be done to prevent the door from prematurely opening which could cause injury.STEP 2: If the door has only one spring and it is broken, proceed to weigh door.STEP 3: If there are two springs, the remaining unbroken spring must be unwound and replaced. Remove all tension COMPLETELY from the torsion spring. DO NOT loosen any set screws on the spring winding cones. Insert the 1/4" insert bit in the drill and engage the bit or 7/16" socket wrench on the drive shaft of the winding unit and rotate the drive shaft counterclockwise to remove tension from the spring (Illus. 1).NOTE: High drill RPM may cause lubricant to come out of the winding unit. All tension in the spring is removed when the line (or description) on the spring is in a straight line. There should be no tension on the torsion cables, and the shaft should rotate freely. Proceed to weigh the door.
Pam Zeman
Reviewed in the United States on September 30, 2024
Works as expected
Kris Underhill
Reviewed in the United States on August 27, 2023
Everything it said it was. Fit well
BA
Reviewed in the United States on August 25, 2023
This spring failed 6 months after installation and the seller is hiding behind the Amazon 30 day return policy. Don’t buy this product.
Kurt Gundersen
Reviewed in the United States on February 8, 2023
Installed it in about 2 hours. Had to take the rod off that holds both wheel end bearings. Removed the old broken spring and slid on the new one. Put new cables turned the end bearings to put tension on the cables and tightened down one of the allen screws. Had to adjust tension in the spring. Make sure you have enough weight on the door tension so it will close properly.
WLG347
Reviewed in the United States on June 6, 2022
OEM replacement spring. Still working.
KarlaT
Reviewed in the United States on December 10, 2022
Arrived early and was the exact part we needed. Trying to buy locally would have taken a month to receive and a LOT more money too.
DM
Reviewed in the United States on November 14, 2022
25 minutes tops to replace my broken spring no hassle with disassembly to operational
Customer
Reviewed in the United States on July 13, 2021
comes ready to install just slide it on the pipe tighten the set screws and use a drill or driver to tighten the spring. this step is the most critical step under tight will cause the cables to come of the wheel! over tight will cause the door to stop when it is closing because the sensors think the door had hit an object.When opening the door for the first time stop it often and check the cables to make sure they have tension if they dont lower the door and tighten the spring making sure the cable stays on track. if you over tighten then the door will stop when closing. when you get it adjusted your done EASY!!!
Recommended Products
$127.88
$ 51 .99 $51.99
$32.40
$ 14 .99 $14.99
$21.79
$ 10 .99 $10.99
$13.99
$ 6 .99 $6.99
$37.23
$ 16 .99 $16.99