Your cart is empty.
Your cart is empty.Create a stunning hardline custom cooling loop with the CORSAIR Hydro X Series XT Hardline Bending Kit, containing the high-quality tools you need to cut and bend 12mm or 14mm hardline tubing. A fine-toothed hacksaw and deburring tool let you cut and smooth your tubing, while a bending mandrel helps create perfect 45°, 90°, and 180° bends.
cindy
Reviewed in the United States on July 1, 2024
The performance was amazing, it did its job and was very easy to use, the fit was Amazon and it had to be based on your tube size, no leakage at all, the fit was crazy, it’s worth the price!
Mestredom
Reviewed in the Netherlands on March 13, 2024
as described
Joseph L.
Reviewed in the United States on February 10, 2024
I want to start off by saying my rating is likely due to this being my first time setting up water cooling, working with bending pipe, and the frustration that comes with it. To start off, the cutting jig was made of plastic. I would assume it's primary purpose alongside holding the pipe is to ensure you're sawing straight. It was very easy to saw into/shave off the cutting jig's material without noticing. The tightening screws were sharp enough to leave marks on the hardline due to being metal. Next, the bending mandrel is also plastic, so it didn't seem optimal with using a heat gun anywhere near it. Whilst being careful heating the pipe, it had melted. It was also not useful if you planned to do more than one angle on the same pipe. I didn't have any issue with the saw or deburring tool, but at this point, half the bundled goods were useless. I would suggest spending just a little bit more for a bending kit made with more optimal materials.
Customer
Reviewed in the United States on December 30, 2024
OK
Darian L. Vorlick
Reviewed in the United States on December 27, 2024
Super convenient if you’re new to heat bending hard tubing. A lot of experienced water cooling builders have their own methods based on experience but if you’re starting off, the tools included really help you learn. My first bends came out amazing thanks to this set.
Steve
Reviewed in the United States on September 15, 2023
It's not the fault of Corsair, it's just the nature of a hacksaw. You will want to sand the cut on a flat surface to get it even. I ended up buying a 12in miter saw in the long run.
TheRockGT
Reviewed in Belgium on November 22, 2023
Pour monter soit même son watercooling c'est le top 👌
Eldern lord 1234
Reviewed in Australia on October 19, 2023
Save $100 and buy $5 twistie tube cutters and a $5 silicone bending insert. Also not compatible with 16mm tubing
Rik
Reviewed in the United States on January 14, 2023
Really nice kit. Should be standard issue to hard tubing enthusiasts. I'm even using the saw to cut 1/4" flat acrylic, and it works great for that, too!
Customer
Reviewed in the United Kingdom on June 18, 2021
The hacksaw is cheaply made out of plastic and the saw blade is at an angle, making a clean straight cut impossible. You can try align the blade properly and tighten in place, but it seems to move again during use.Chamfer tool and bending tool are not exclusive to Corsair or this set and can be bought separate for cheap.I used the cutting jig with 14mm OD clear satin tubing from Corsair. Putting the tubing in the jig took away some of the satin finish, ruining the look of the tubing. The jig is also just cheap feeling and awkward to use in general and with it being made out of plastic, it’s very easy to cut into by mistake, especially with the angled hacksaw blade as mentioned above.
Ben Schylling
Reviewed in the United States on March 26, 2021
Terrible product. The hack saw is incredibly cheap quality and the cutting brace is sloped so you can not achieve a clean cut. The corsair VTubing is also one of the worst products I have ever used. It is incredibly brittle and will break and shatter with almost any tension. I will not be using corsair ever again for water cooling.
scott
Reviewed in the United States on February 14, 2021
Overall this set up is a must for the Corsair Hardline series tubes as any other cutting device will break or shatter the Corsair tubing. It takes technique such as not using hard pressure but long soft stokes to get a "fairly" straight cut. The miter box helps, but a perfect cut is non existent. If you want to save money, just go to hardware store and get a small hand saw, order a 30 cm long silicone insert, a metal drill ran reamer as this plastic handheld one will get the job done so you can insert tube in fitting, but it will look terrible. The tool to help with bending angles did not work for me personally, but it may for someone else. Save your money and just get those items elsewhere.
J19
Reviewed in Spain on November 20, 2021
lo mejor la pieza naranja para redondear y la sierra, la silicona es muy corta y el doblador muy inútil pero bueno hace su "función"
Recommended Products
