Your cart is empty.
Your cart is empty.Product Description
Stainless Steel Horizontal Centrifugal Pump & Motor
- Reliable single stage or multistage impeller designs
- All stainless steel wet end construction for reliability
- Able to pump hot water up to 158°F
- Carbon/Ceramic mechanical seal for reliable operation
- Higher than normal 120°F ambient temperature rating
- High operating temperature and high current draw protection
- Robust TEFC motor constructed from corrosion resistant materials
- IP55 international protection rating for dust and dirt
- Permanently split capacitor for reliable starting
- Motor and pump are designed for frequent starts
Torrium 2 Controller
- Larger water pathway provides superior hydraulic performance
- Adaptive starting - monitors incoming pressure
- Quick cut-in for constant flow and even water pressure
- Extra Draw off Capacity w/ Built In Accumulator
- Easy status check LED's
- Dry run protection with auto restart
- High Water Temp, Excessive Electrical Current and Power Surge Protection
- Corrosion & Scale Resistance
- Vertical/horizontal 360° discharge
- Power Cable - 6 ft power cord with standard NEMA power plug
Choose from five different models with varying performance curves for most any application.
Hydraulic Performance is the amount of pressure boost the pump will add to your incoming pressure at a specific flow rate. Select the best pump for your application based upon your existing incoming pressure and desired combined system pressure (Usually < 80 psi to meet local building codes.)
Model / Voltage / Incoming Pressure Range
- BT14-30 / 120V / 22-60 psi Incoming Pressure
- BT14-45 / 120V / 2-40 psi Incoming Pressure
- BT20-30 / 120V / 10-50 psi Incoming Pressure
- BT20-40 / 240V / 0-20 psi Incoming Pressure
- BT30-30 / 240V / 10-50 psi Incoming Pressure
Note: Do not exceed a Maximum System Pressure of 100 psi (incoming pressure PLUS pump boost).
Jeff H
Reviewed in the United States on February 12, 2024
This is my second pump, the first lasted 8 years which I have no complaints. Easy install and does the job!
Dustin Bairfield
Reviewed in the United States on January 3, 2024
Added about 30 psi , super quiet, great product
DAVID STANCIL
Reviewed in the United States on September 2, 2020
So far so good
Nathan B
Reviewed in the United States on July 29, 2020
Extremely well engineered and constructed pump.
Andy
Reviewed in the United States on March 8, 2019
I bought this pump to replace an aging Davey FS18-40. I have 30 psi municipal supply and the pump boosts the pressure to 80 psi deadhead. have a regulator on the discharge side but not on the suction. I was overpressuring the FS but the 30-30 is able to handle the relatively high inlet pressure.The pump is quiet which the aging pump was not. I had replaced the seals twice in the 15 years and this new guy Will actually require less maintenance since has fewer stages and suited for the inlet.We have a 6 bedroom house and with the 30-30s flat curve one can push a lot of water at a good pressure. It is particularly good if you have a high water use for irrigation as well as your house.I actually spent very little time choosing it and then kicked. Myself for not ordering one of the higher pressure pumps. Dave at primo, cleared me up that the pump was best for my high inlet pressure and it was a direct fit for my FS. In fact it took me 20 minutes tops to remove old pumpand install because no piping changesvwere required and the 220 plug was just like FS. I simply cut a 5/4 decking board to make up the 1 incch lower elevating of the 30-30 versus the FS. Oh, and the 1 1/4 inlet was just like my FS.If you’re installing it from scratch, I recommend SharkBite fittings. My plumber used these on my initial install and no solder no leaks. Make it easy on yourself. Be sure to provide a bypass with valve so you can still run if you need it sometime.Davey makes very good pumps and this is a top product. Very satisfied. I don’t give five star ratings for stuff unless it is a steal.
Recommended Products