Shopping Cart

Your cart is empty.

Your cart is empty.

Delay Relay Module DC12V 0-120min Adjustable Timer On/Off Time Delay Relay Timing Switch Module Board Delay for Industrial Control(DC 12V 0-120min)

Free shipping on orders over $29.99

$7.59

$ 3 .99 $3.99

In Stock

About this item

  • [Adjustable Timer Module]: Both "on" time and "off" time of this timer switch module are adjustable to meet different needs
  • [Specification]: DC12V, 0-120min; Quiescent Current: <10mA; Load acity: 10A(AC 0-250V, DC 0-30V); Size: 70*20*18mm/2.75*0.78*0.7"
  • [2 Timing Delay Modes]: The timer module support 2 modes; Mon mode (once) and cycle mode, and you can simply switch mode by adjusting the jumper
  • [Application]: This adjustable timer relay could be used on timer operating equipment; Suitable for robotics, car lamp delay, intelligent electronic product development
  • [Stable Performance]: This is a delay relay module board with high , it offers stable and reliable performance



Product Description

GS01336-03-1
YT

Features:


  • It is a timer relay module with high precision, stable and reliable performance.
  • Support 2 modes, mon mode(once) and cycle mode, and you can simply switch mode by adjusting the jumper.
  • Connect 2 wires of &quot;Key&quot; if you need module to work recurrently after power on.
  • There are many voltage and time range for your choice, both &quot;on&quot; time and &quot;off&quot; time are adjustable.
  • Widely used on timer operating equipment, machine repetitive test circuit, fish tank intermittent pump, etc.

1

GS01336-03-2

GS01336-03-3

1

GS01336-03-2

GS01336-03-3

Specifications:

Type: DC12V,0-120min

Dynamic Current: 45mA@12V; 90mA@5V; 30mA@24V

Load acity: 10A(AC0-250V, DC0-30V)

Size: 70*20*18mm / 2.75*0.78*0.7&quot;

Time Accuracy: Max value*0.001

Mon. Mode:

1. The module Power-on, When triggered the relay is switched on, timer delay off.

2. When triggered on the delay process, again triggered, it will immediately interrupt the delay.

Cycle Mode:

1. The module Power-on, When triggered the relay is switched on, (T1) timer delay off. (T2) timer delay

on. Such cycle. T1 and T2 are set by two adjustable resistors, respectively.

2. When triggered on the delay process, again triggered, it will immediately interrupt the delay.

1 x Timer Relay Module


Julie M
Reviewed in Canada on January 19, 2025
It's a 1-shot timer when triggered in Mon mode and cycles forever when triggered in Cycle mode.Triggering again the Cycle mode stops it until triggered again. Timing trim pots are finicky and full CW are the shortest times, fully CCW are the longest times.
Skip
Reviewed in the United States on April 19, 2024
I've uses several of these. One cycles a circulating fan in my RV fridge. Another probides a delayed of for lights. Sort of finicky to get desired timing.
Customer
Reviewed in the United States on June 5, 2023
If you are a hobbyist this inexpensive module is for you ! I made a bench test and found that the time control adjustments are backwards to what we are normally used to, turn it COUNTER CLOCK WISE to increase the time. Note that the shorting clips can change the timing from 120 minute to 12 minutes, and the other clip changes the cycling from on-off-on-off etc, to one shot on and off. I found the mounting holes too close to the input and output connectors, so I removed these connectors and soldered wires to them directly. I also used an old dc power module found on many electronics to power it up.
A
Reviewed in Canada on September 21, 2022
Doesn't work for what I wanted to use it for as the minimum time range was misleading. The description says 0-120min but realistically 0s doesn't make any sense and T/10 was super vague.I had to trial and error test it with a stop watch to find out the shortest time was 4min. If you max out the potentiometer that almost doubles to just under 8 minutes. If you want anything less than 4min try something else.I should also mention that the trigger button behavior is momentary and will switch between states.IE: press it and it'll turn on, press it again it'll turn off, regardless of the delay cycle. Probably what most people are expecting but for my project I really just needed the ON state only, subsequent presses shouldn't do anything until it turns off automatically.
Noel
Reviewed in the United States on February 19, 2022
i tried everything so did my electrical friend. the settings don't work, this is a scam.