Shopping Cart

Your cart is empty.

Your cart is empty.

Dual Motor Set for Electric Skateboard 90mm Powered 10S 36V DIY Brushless Hub Motor Kit for Longboard Upgraded 77kv 400W 30 mph top Speed Skateboarding Equipment

Free shipping on orders over $29.99

$159.00

$ 73 .99 $73.99

In Stock

About this item

  • 【Upgraded】Puaida upgraded 90mm Powered Dual Hub Motor Kit DIY Electric Skateboard set,compatible with dual hub motor esc ,not compatible with belt drive esc,for vesc you need to know how to set the parameters
  • 【30mph】77kv ,With Puaida's ESC , its running speed goes up to 30 mph and it’s strong enough to climb a 25% steep hill.,please note that you may get much lower top speed if you are not using the puaida's esc ,and if you are a heavier rider ,you may also get a bit lower speed.
  • 【Elastic PU】Black longboard wheel is made of high elastic PU material, more durable and longer life
  • 【Assembled】All the parts are assembled,easy to install on the electric skateboard, You can diy an longboard or short board and make your own skateboard
  • 【High Load Capacity】The maximum load capacity reaches 220.46 lbs, allowing every rider to electric skateboard happily!



Product Description

Model DM400
Voltage 36V
Idle speed 2900±5% rpm
load speed 2550±5% rpm
The rated torque ≥1.15 N.m
Rated current ≤11 A
Effective rate ≥76%
Maximum permissible power 400 W
Working system S2 60 (min)
Protection grade IP33
Insulation class E
Phase Angle 120°
The stator slot number 18
The number of the rotor 20
motor sleeve

Tire removal

1. Remove the five screws using a wrench

2. Remove the protective cover

3. Remove the tire

When taking out the tire, you can gently knock out part of the tire with a small hammer and then take it by hand. The protective cover plate can be used to be removed with the tire.

Tire installation

1. Load the tire into the motor, and pay attention to align the through-hole of the tire skeleton with the corresponding threaded hole of the motor when it is fast in place.

2. Reverse install the protective cover to the end face of the tire support frame, and pay attention to the alignment of several holes.

3. Tighten the five screws using a wrench.


Ian
Reviewed in the United States on April 7, 2025
The media could not be loaded.
JiG£∆B
Reviewed in the United States on February 28, 2024
Haven't had a chance to hook them up yet they only come with the two motors and nothing else so I have to buy everything else. Not compatible I guess with other skateboard units.
spacemonkey58
Reviewed in the United States on December 6, 2024
I'm using these (slightly modified with a 3d printed end to hold 2 opposite end bearings) to power a rail cart. I've run them hard for the past 2 months without a hiccup.I use them with their esc control kit. The torque, speed and braking are totally tweak-able.On the control kit, the ARMING BUTTON solder joints easily break. I re-soldered and reinforced with a glue gun. That's the only negative so far.
Nes
Reviewed in the United States on September 5, 2023
I got everything in the box as stated, I just thought a T tool would have been thrown in.
Travis B
Reviewed in the United States on September 23, 2023
The media could not be loaded.
Maxime T
Reviewed in Canada on August 4, 2023
These are not 400W, they are GF055 300W... Thanks for the lies..
Joe T
Reviewed in the United States on August 11, 2022
Does not go 30mph. Even with 105mm wheels. Nothing special about these. My generic set rated at “300w” was faster. With a high output 10s3p battery.I thought getting a good battery would make these hub motors better than the rest. I was wrong.I got these specifically to go 30mph as they stated. Even downhill they will not pass 30mph. With their control. And the best 36v battery fully charged.Ide say good quality wires. And motors. And the control they sell separately for somebody who wants the fancy plugs and a decent remote with battery level.Also the speed on the remote is wrong. And can’t seem to dial it in with the remote settings.When they specifically say 30mph with 105mm I spend the extra $160 on wheels that fit and $350 on a battery and now everything is great besides the slow speed.Motors could be defective as well as they heat up so hot even just going around the block with no incline.Also when I got these there was no reviews. And here I am. They work. They roll, they are clean and plug in and the censored wheels work smooth. Smooth start. Breaking is terrible compared to other generic controls. And motors.Good for reliable setup for a person that does not want to pass 25mph. But for me I was here for 30mph and I am not happy.
Guilherme Portela
Reviewed in the United States on May 13, 2022
Got here in time, installed on my teamgee h20 mini, little sable at the start because it needs tuning via ECU, but it’s very fast, got up to 26mph, forgot to tighten the truck and speed wobble got me bad, but I’m fine, very nice motor, let’s see how long it’s going to last 🤣Btw: the teamgee had some motor problems so I decided to get this one to replace and work very good
Brennen
Reviewed in the United States on February 24, 2022
These motors paired with the puaida speed controller and remote made this electric skateboard build a breeze. Everything looks to be of very high quality. I was able to reach a top speed of 30 mph according to the remote. These motors have plenty speed and torque for any size rider. I would highly recommend these.
Recommended Products