Shopping Cart

Your cart is empty.

Your cart is empty.

ECCPP 4PCS 1 inch 4 Lug Wheel Spacers 4x137mm to 4x137mm fits for Bayou 300 400 for Mule 500 100 500 520 550 600 for Brute Force 650

4.5 (7) Write Review
Free shipping on orders over $29.99

$69.99

$ 28 .99 $28.99

In Stock

1.Size:2pcs


  • SPECIFICATIONS-- Wheel Spacers 4 LUG with 4x137 bolt pattern,110mm Center bore,M10x1.25 thread pitch,1"(25mm) thick
  • Compatibility-- Fit for 2003-2005 for Outlander 330 2x4 HO;2003-2005 for Outlander 330 4x4 HO;2003-2006 for Outlander 400 4x4 HO
  • About the thickness-- Please confirm about the Fender Gap,this decides the thickness range should be fitted. For a car without leveling lifting,to Av-oid rubbing,the thickness of wheel adapters should be less than the fender gap. For example,if your fender gap is 1",It is better to choose spacers which is less than 1" thick
  • BENEFITS--The 4x137 wheel spacer Widen your vehicle wheels base by allowing for a more aggressive stance, rubbing easily and instantly,greatly improve the vehicle stability! Box Packaged,bolt-on easy installation,save your time and money!
  • MANUFACTURE--The body of wheel adapters 4 lug is made of Forged aluminum. Meanwhile Forged heat-treated and hardened ISO/DIN 10.9 studs deliver strength


Product Description

wheel spacers

Fitments

for: 2011-2013 for Can-Am Outlander 800R 4x4 EFI || 2012-2013 for Can-Am Outlander 800R 4x4 XMR EFI
for: 2011-2013 for Can-Am Outlander 800R 4x4 XT EFI || 2010-2013 for Can-Am Outlander 800R 4x4 XTP EFI
for: 1990-2004 for Kawasaki Bayou 300 KLF300B || 1990-2004 for Kawasaki Bayou 300 KLF300C 4x4
for: 07-08 for Kawasaki Brute Force 650 KVF650H 4x4i || 06-2013 for Kawasaki Brute Force 650 KVF650F 4x4i || 93-99 for Kawasaki Bayou 400 KLF400B 4x4

fit for

  • This spacer adapter includes open end lug nuts to secure the spacers onto your factory hubs

If your factory thread size is different Need to purchase a set of open end lug nuts in the correct thread pitch (your factory thread pitch) to complete the installation

Your Factory wheel studs may extend past the surface of the wheel spacers. In this case you will need to:

1) Shorten the factory studs

2) The wheels need to have the open slots (cavities) between mounting holes.

3) Purchase a set of shorter studs and replace them with the factory studs.

The video showcases the product in use.The video guides you through product setup.The video compares multiple products.The video shows the product being unpacked.

hero-video

Merchant Video
wheel spacers
wheel spacers

Russ P
Reviewed in the United States on April 4, 2025
These took some work to install. As soon as 2 of the lug nuts were snug (not tight) the socket would not fit on the others. I found that a Craftsman socket was slightly smaller in diameter and was able to get these installed. Once installed they worked perfectly. Well balanced and increased my stance width by 2 inches. These were installed on a 2023 Can-Am SportMax 1000r DPS.
Debra L Bailer
Reviewed in the United States on April 20, 2024
They fit my 2023 Kawasaki Mule SX XC perfectly! Excellent quality, fast shipping. These 1” spacers are excellent quality at an unbelievable price. I would recommend to everyone!
Ashgrimm
Reviewed in the United States on April 12, 2024
I used these to bring the wheel spacing out on my rear wheels and run one size tire on all 4,These worked and fit well.
Shelby Monroe
Reviewed in the United States on July 8, 2023
They fit ok. Little bit tight for the wheel holes but seemed out and worked fine.
Rick
Reviewed in the United States on November 27, 2023
These don't fit 4x137
Bryan Becker
Reviewed in the United States on October 16, 2021
1992 Kawasaki Bayou 4x4. Worked well. Didn’t want to get too wide. With the current wheels and tires, the offset is almost straight from front to back to allow for stability and clearance. Very nice!
Zach McCarty
Reviewed in the United States on February 12, 2020
Good quality. Didn’t quite fit my teryx, but after a little boring, they went on.