Your cart is empty.
Your cart is empty.Ejo18
Reviewed in the United States on May 15, 2025
Need to use original screws for install. Front had 3 holes but only 2 can be used as only 2 screws provided by chevrolet.
Customer
Reviewed in Canada on April 25, 2025
Easy to put on and gives the trailblazer a good look. Molded flaps also work well to keep the spray down. Did a burnout in a puddle and my wife didn’t get sprayed in the FACE! (Darn) product is good.
Sport Rider Inc
Reviewed in the United States on September 17, 2024
The instructions say "remove exisiting screws". There are NO screws to remove. The only thing holding these mudflaps on are the screws provided screwing into the inner fender liner - which is thin material with no support. Tried mounting one of these up and it was a joke. Didn't waste my time trying the others. Buy factory GM ones.
GIMMEFUEL
Reviewed in the United States on February 27, 2024
We got these for my wife’s ‘24 Trailblazer RS. VERY pleased & pleasantly surprised with them. The fit was SO spot on, I could have probably just “thrown” them at the car & they would have went on themselves. The fit is perfect & they look great. They come with screws, but the install is so spot on, I just used the OEM fasteners that were already there. I doubt that there is a higher quality mud guard that you could buy for this vehicle. Definitely impressed with these & would highly recommend. 👍🏻👍🏻
Spikey59
Reviewed in the United States on February 24, 2024
Product looks good and fixed perfect to my SUV but on the installation I had to use my own tool because the one provided it did not fit properly. In regards to durability, time will tell if they're strong quality to remain in good condition. Overall, they're good for the price and looks nice on my truck.
Customer
Reviewed in Canada on November 3, 2024
Tel que vu
Wyntendo
Reviewed in the United States on October 31, 2024
I have a 2024 Trailblazer Activ, and these splash guards fit perfectly.I think the material is ever so slightly not the same as the rest of the standard fender flares, etc, but it matches close enough that it doesn't really matter.Installing, I used factory screws as others recommended - didn't even look at the ones that came with it, and not sure why you would. No install issues - took about 10 minutes (seriously) to install all 4.Fits well, and looks good. Can't wait for winter!
Martial Pruno
Reviewed in Canada on October 13, 2024
Fait aussi sut Bolt EUV ...juste quelques trous à percer dans les garde-boues
Craig Johnson
Reviewed in the United States on January 8, 2024
If you are looking for a set of mud flaps for the new generation Trailblazer, look no further! These are really good and easy to install. I was able to install both the front a the rear on both sides in less than a half hour. The installation holes line up perfectly with the fender screws. I did not need to use the screws included in the box. Honestly the hardest part was finding tools to fit in tight spaces. I ended up using a smaller socket that allowed for a T15 bit and used a socket wrench to remove and reinstall the factory screws.
Brian M.
Reviewed in Canada on April 18, 2024
Very thin and cheap, front guards did not fit the profile. Will do but dealer suppled would be better.
Barb Skog
Reviewed in Canada on September 22, 2023
The back ones fit perfectly but the front ones didn’t quite fit the contour
Kindle Customer
Reviewed in the United States on July 15, 2023
These fit like a glove! I have a 2023 trailblazer and they fit perfectly! However the tool it comes with will not work to get the factory screws off as it is too big. Also they do not send enough screws. You get 8 in the box but you would really need 12 total. It is a moot point though as the screws they send are too big and do not fit. So I used the factory screws and it works perfectly with those! Overall a great product for the price!
John Boy
Reviewed in the United States on November 8, 2020
This is review is for a 2021 Chevy Trailblazer:I order the Splash guards on Saturday and they arrived the next DAY!!! WOW. When I open the box I looked for any kind of instructions and none to be found so I was little skeptical of the product. I then read reviews on installation and it seemed pretty straight forward. So I went out to the garage and placed to Guards to where they would be mounted and to my surprise they lined up perfectly with the screws that hold in the wheel well liner. The front were easy because I used my electric driver to mount the guards after turning the wheel out of the way. The rears I use my small ratchet socket. The rear guards also had a screw mount under the flaps for extra STABILITY great idea. The front guards also had an extra mounting hole but the there was now screw at this location on the wheel well liner. I then used the screws that came with the guards in this position after drilling a little pilot hole.These guards look great as if they were custom made. Oh, maybe they were for the TB.EXCELLENT PRODUCT!!!!!
Recommended Products