Your cart is empty.
Your cart is empty.Product Description
High Torque Electric DC Reversible Motor with Self-locking Worm Geared Motor Threaded/D Shaft Can be Chosen
12/24 Volt DC Driver Motor for Robot, Volume Gate Garage Door, Milling Machine, Home Projects, Manufacturing Industry and So On
- Precision casting, exquisite output shaft, low noise, more comfortable to use；
- The gears are heat-treated after grinding, with wear resistance, long life, low noise;
- The positive and negative wiring use high quality PP anti-electric waterproof, wear resistance is not easy break;
- The Gears made of copper alloy, have advantages of good wear resistance, corrosion resistance, smoothly transmission and higher torque transmission.
There are Left/Right and Threaded/Double Flat Shafts for your choice, There must be one pattern ideal for you;
The positive and negative wiring use high quality PP anti-electric waterproof, wear resistance is not easy break;
The reason for choosing this motor is copper alloy gears, can make sure of low noise, smooth and high torque transmission, wear resistance and long life.
Gators galore
Reviewed in Australia on January 10, 2025
Used to replace drive motor on Toro pro blower chute. Just needed to buy a pulley to suit
earl
Reviewed in Canada on June 18, 2024
It’s as advertised
James Kirkley
Reviewed in the United States on May 29, 2024
Using this and the mirror image motor for a lift table. Very happy with the motor build quality.
Prime member CM
Reviewed in the United States on April 24, 2024
The cut drive slot design and the motor angle nearly match the original motor for the legacy 25 60" deck height adjustment. The motor shaft drive was not an exact fit and I had to use a square file to file the slot on the drive nut or coupler. But that wasn't enough. I had to use a short collar or cut of tubing for a spacer since the shaft was cut deeper or the shaft not long enough to extend past the mounting bracket. There was no nut but it is metric. I don't know if the speed matters as long as the screw for the adjuster isn't binding. I rarely adjust the deck, unless the grass is too high for one cut. This motor completes the original 12 volt control for the deck far cheaper than the original or replacement and it's higher cost.
Hummerguy
Reviewed in the United States on December 3, 2023
Works very well to drive the directional control for my snow blower. Has plenty of torque to drive the screw even when iced up. Very happy.
James
Reviewed in the United States on December 14, 2023
Small size with lot of torque. Used two of these to pull carrage on a small sawmill
Liltod
Reviewed in Australia on October 20, 2022
Good for a project winch job
PeteOn
Reviewed in the United States on March 21, 2021
This is a perfect setup for the application I had. Having bought a tractor with a cab, the manual chute rotation crank became a mystery as it stays outside the cab. So I cut it down in length and then mounted this motor on the end of the shaft, operable by a reversing momentary switch in the cab and piggybacking power off from a spot on the in-cab fuse box.My proof of concept prototype was a stripped down 12v cordless drill. This was good but in fitting things into a pvc waterproof container, I lost the variable speed trigger; "on" was ALL on. This new motor has a significant gear reduction that allows some considerable comfort in time on changing chute position.For such an application, remember that this motor housing is NOT waterproof: using some butyl tape and household goop, I have sealed its exterior so it seems impervious to the ice, water and snow inherent in the application. The goop also was instrumental in waterproofing the electrical connections.For such application, consider the mechanical supports required for attachment and how attachment will be made from the arbor shaft to the device. The Climax Part RC-037 Mild Steel, Black Oxide Plating Rigid Coupling, 3/8 inch bore, 3/4 inch OD, 1 inch Length, 1/4-20 x 3/16 Set Screw that was ordered with this does not exactly fit on the shaft. Much filing to get the two to fit, but its a work.
serge savoie
Reviewed in Canada on October 21, 2021
marche pied motorise parfait
Kevin W
Reviewed in the United States on April 18, 2021
Update:Driving this with an Arduino and Cytron motor controller. The motor is not too noisy and has plenty of torque for my application. I threw a 60 mm pulley on top and was unable to stop it with my bare hands so I'm pretty confident that it'll hold up to other applications once I actually throw a smaller gear on it for the extra mechanical advantage that provides.My only complaint might be that the shaft isn't very tall. Using a 3d printed gear or pulley would require me to sacrifice strength in order to get a nut far enough onto the threads to secure it well. Me and my team ended up taking the drive apart and found it's driven with metal gears, so that should hold up for a long time. Additionally we we able to easily cut off the threaded end of the shaft and weld on a longer shaft for our project.My only complaint, and it's really to be expected, is that using the PWM to speed control the motor generates a whine in the motor and the motor can easily stall at the slower speeds. I think that's just the nature of how we're using this motor.
Andrew K.
Reviewed in the United States on November 26, 2020
Used to make a boat prop spin for walk mounting. Still working on it but works great. Just wish it wasn't so noisy but that is to be expected for the heat reductions. I've ran this for a few hours straight and the motor will get up to 130F so just be cautious how long you use it and ensure ventilation (still need to add this in, might add a computer fan and side vents).
LÉO COMEAU
Reviewed in Canada on March 23, 2019
Different motor than the way we needed...
J. Stefanick
Reviewed in the United States on February 19, 2019
Seems to work well but the output shaft is bent. My mount is flexible so it appears to be a non issue.
Recommended Products
$115.95
$ 54 .99 $54.99