Your cart is empty.
Your cart is empty.Product Description
Hablitz
Reviewed in Germany on March 29, 2025
Wirklich eine Top Halterung, super hochwertig, stabil, leicht auf und anzubauen.Man sollte die komplette Halterung zusammenbauen und den PC vor der Montage am Tisch einmal reinstellen um zu testen.Dann montieren und und PC reinstellen. Ich habe mir oben extra 3cm Platz gelassen, damit der Airflow besser ist.Da wackelt nichts, super stabil, bin happy, das längere Warten hat sich absolut gelohnt.Dazu passen kleinere, aber auch sehr geoße Gehäuse. Die Halterung hat keine Verschleißteile und kann beliebig an und abmontiert werden.
Mohammad Javad Najafirad
Reviewed in the United States on April 6, 2025
My PC took to much space on my desk, therefore I needed a pc mount under my desk.The Ultimate Setup pc holder is a great solution which fits my pc perfectly. To be honestits not that easy to install, but the manual instruction is very detailed and included ahelpful drill template so its handleable even with low craftmans skills.For me most important was that my 1000$ pc has a secure place. The pc holder is verystable and robust. The steel material is very thick and nothing woobles. Definitelyrecommended!
Vin No
Reviewed in the United States on April 26, 2025
Easy to assemble, clear instructions, and good quality materials.BEWARE: Doesn't come with wood screws.
JAIME MONCAYO
Reviewed in the United States on April 22, 2025
Missing screws but were very helpful in getting those sent out!
Kenneth Vivero
Reviewed in the United States on April 22, 2025
Did not include wood screws to mount under desk
Tony T
Reviewed in the United States on April 14, 2025
A few minor complaints but very solid and should last forever.Mine apparently had the rubber pads pulled off and replaced because there's dirty glue marks that are going to continuously hold dust until they are caked with it. I tried to reposition them but they were stuck on well enough that it would have just left more glue exposed in a new position, leaving me with the same problem. The only real way to fix this would be to pull the pads up and clean the glue off and then restick them but that's more trouble than I feel like dealing with right now.The directions do say there are wood screws included but this is absolutely not true. Just like everybody else has mentioned, there are no wood screws included with this kit. I used #10 3/4 in wood screws. These worked well.The included drill bit was bent and would have destroyed my desk if I had used it. I recommend turning on your drill and looking at the bit to make sure it doesn't wobble before you start trying to drill with it. I used a 7/16-in bit to drill the pilots for my #10 screws (I think this was the size of the included bit as well but didn't check closely).Adjusting it for sizing the width of the tower can be a bit of a pain if you're wanting everything perfect. Don't try to size it too tightly to the width of the tower or you're likely going to have problems getting it in and out. Flip it upside down on a desk, or solid surface, when connecting the numbered measurement cross bars. Use them for alignment but use a measuring tape for accuracy. Add an extra half an inch so you have plenty of spacing to maneuver your tower in and out.At some point the extra glue is going to drive me insane just knowing it's there collecting dust from my towers bottom intake fan. When I get around to resetting the bottom rubber pads I will probably add some rubber legs to hold the tower up off of the bottom pieces more for better ventilation. I will also go ahead and drill the holes completely through the desk and bolt mount the assembly at that time as well but the wood screws seem to be doing well even with frequent desk height adjustments.
Ben
Reviewed in the United States on April 13, 2025
This PC Holder is sturdy and holds my case securely. Attaching the lower section with a thru bolt design is much more safe than other friction based implementations. There is only a small area required to mount the holder to the bottom of your desk - which fit perfectly between the dual rails of my standing desk.Like others I was missing screws to mount the holder to the desk, but I reached out to the company and they provided alternate screws and said it should be fixed in a future production run.
Customer
Reviewed in the United States on April 13, 2025
I am giving it a five because they are robust, strong and versatile. I’d take half a star off because there were no wood screws in the box and they said there were. Advise.. make sure you have screws before trying to use these… now.. saying that.. they rock and are excellent.
SQ
Reviewed in the United States on April 1, 2025
Just installed this to mount my gaming PC under my sit/stand desk. Product is made with quality and has a well thought out design to allow for dimension customization. My computer is fairly heavy (about 35 pounds so well under the product max weight of 77 pounds) and I have no concerns that this mount will fail structurally, very sturdy. Only gripe is that as others have noted mounting wood screws were not included though I did a nut and bolt approach to give it as much mounting strength as possible. Easy install if you have basic tool use knowledge. But minus one star because if you say you are going to include something you should. I would recommend
Recommended Products