Your cart is empty.
Your cart is empty.
Rear Bumper Protector Guards
Our rear Bumper Protector Guards reduces the risk of scuffs, scratches and other signs of damage caused by factors beyond your control.
Compatible with:
Chrysler Pacifica 2017-2024
Chrysler Voyager 2020-2024
Function
One year warranty to protect your shopping. If a product has a rare quality problem, we will replace it for you anytime within one year of your order. If you do have a problem, we will do everything we can to help you.
Easy Installation
Simply use our own 3M adhesive tape for easy installation without drilling holes, saving you time!
Quality
Designed for long term use, our rear bumper protectors are heat and friction resistant with a non-slip textured surface.
Product Protection
One year warranty to protect your shopping. If a product has a rare quality problem, we will replace it for you anytime within one year of your order. If you do have a problem, we will do everything we can to help you.
BDK
Reviewed in the United States on May 8, 2025
Good protection for sliding things in and out of the back of a minivan. Installed it on a 2023 Chrysler Pacifica Touring L model. I waited until the temps were in the 70's before trying to install it. It comes with a small arrow to help line up in the center (using the latch as a mid-point). It comes with 2 packs of adhesive promotor which is nice. I wiped the bumper down with isopropyl alcohol before applying the promoter. The ridge sits on the big curve down of the bumper, but you have to be a little careful keeping an eye on the top of it to make sure you have consistent spacing from the latch side (the ridge itself won't automatically get perfect alignment). I folded into a 'U' with both hands and aligned the center first, then doing one side at a time slowly aligned the guard while pushing it down moving towards the outside of the van. It came out pretty straight and aligned. Only knock would be is it was shipped to me folded down the middle. I ended up leaving it in the sun for about 30 minutes with some weight on the crease and it straightened it out for the most part, at least enough where it doesn't effect you trying to line up the center when starting the install. Seems like a good value price wise compared to others I googled, which appeared more expensive.
HENRY JASPE
Reviewed in the United States on May 29, 2025
After a few too many close calls with parallel parking, I decided to invest in the Kefly rear bumper protector for my Chrysler Pacifica. Installation was a breeze with the 3M adhesive tape, no tools or drilling needed, and it securely fit my 2020 model. It has already proven its worth by preventing several scratches during grocery runs and family outings. The non-slip texture also helps when loading stuff into the trunk, as it adds grip. I appreciate the peace of mind it gives, especially in crowded parking lots. The look is subtle enough that it doesn’t take away from the car’s aesthetics. While it’s only been a couple of months, the bumper protector seems designed to withstand various weather conditions without showing wear. It’s a smart investment for maintaining my car’s exterior.
DP
Reviewed in the United States on May 26, 2025
I installed this bumper protector on my 2018 Chrysler Pacifica today. It covered up a few nicks and scratches that it has incurred over the years. The first thing you must do before attaching the protector is to make sure the surface is clean and prepped. I first cleaned it with a damp rag and then opened one of the included "primer" packets. The towelettes are enclosed in an aluminized plastic packet much like the ones that you may find for cleaning your computer screen or prepping a cellphone display before applying a screen protector. Unfortunately the towelettes in both packets were bone dry so I used some alcohol on a rag instead to prep the surface. The bumper protector comes with double stick tape preapplied so all you have to do is peel off the plastic that protects it. In my opinion there could have been more tape applied and it seems like the adhesion of the tape may not be enough. Time will tell. There is also no real way to align the bumper guard other than just eyeing it. After application it looks nice and if it stays that way I'll be satisfied. I'm just a little dubious about whether it will stay attached over the long haul.
Brian Mummery
Reviewed in Canada on May 19, 2025
The item is well made BUT it is shipped folded in half which makes it impossible to to straighten. so doesn't lay well.
Jesse
Reviewed in the United States on May 12, 2025
The bumper had gotten scuffed up after moving big stuff in and out of the trunk. I'm relieved to have found this great protector strip! It covered up some scuff marks, and it'll prevent new ones.Its a type of firm foam like the kind they use for cheaper shoe soles. My kids shoes and my house shoes have it. That's what it feels like anyway. It has two long strips of VHB-style tape and several smaller strips along the middle that stick it to the paint. I don't think it will be falling off any time soon. I installed the pad two days ago and pressure washed the van this morning. The pad didn't budge. I recommend it!Note: the pad comes folded in half. When you unfold it, the middle will still look splayed out a bit. Once it's stuck down, it's less noticeable, but does not go away completely. I though about taking a heat gun to it gently, but I figure the sun will take care of it once it gets a little hotter here.
Scott
Reviewed in the United States on May 11, 2025
I really didn't know what to expect, but the finished product looked amazing! Better than anything from the factory - the material is perfect for the Pacifica. It has a faint hexagon pattern to it giving it texture and dimension. It also has a tiny lip at the edge which should run just atop the outer/upper edge of the bumper.It didn't come with any instructions, but my advice is this: take your time. There are short pieces of tape that run 'vertical' compared to the two long 'horizontal pieces. There's also a very faint indicator of the center of the piece. Line up the center with the center of the bumper, and once you have the position, get one end of the cover started. Just pull a few inches of the red tape from each 'horizontal' piece, and progressively move to the next 'vertical' piece, pull more red tape from the horizontal pieces, pushing the material into place. Gradually work this way all the way to the other end (see the final photo to see my 'halfway' progress point). The final product looks spectacular! I couldn't be happier with the results! Not only does it protect my bumper edge moving forward, but it conceals the pre-existing scratches.
Recommended Products
$102.99
$ 47 .99 $47.99
$64.99
$ 29 .99 $29.99
$61.95
$ 25 .99 $25.99