Your cart is empty.
Your cart is empty.Emiliano L. Maiello
Reviewed in Canada on September 6, 2014
Nice color, finally my Lock it's not orange and black anymore..It's not so complicate to install honestly, just follow the instructions inside and in 10 minutes your lock will be better than new...do not skip the part with the hot water and soap...they are really important!
Jonathan
Reviewed in the United States on June 10, 2014
There are many different colors you can choose from the store. And, some of the colors seems interesting.However, the problem is not from the color. while you getting the product on hand, you may feel a little bit shock. Then you may try to use it on your lock, but it does not work well on it!!!!So, I return it.
themonkrat
Reviewed in the United States on December 12, 2014
At first I was hesitant to buy this as a lot of the reviews focused on how difficult the skin was to apply. However, I had absolutely no difficulty. What might have helped is that I used very hot water, let it soak for a full three minutes, and I put a lid on the bowl I used to keep more of the heat in.The skin slid on very easily. What I wish I did differently was to cut the skin to the correct length before putting it on. I was able to cut the excess skin off, but I feel it would have been a little easier to cut it while off of the shackle.I bought this for two reasons. I love the color white and this skin certainly expresses that. The lock now is very striking and goes better with my white bike. (Now to find a better-looking cable to match!) Also, the rubber cap on my lock was broken and exposed the end of the lock, allowing it to rust and sometimes freeze when water got in.This was so easy I wish I had installed it months ago when I first purchased it. Do not let those other reviews put you off!
Ali
Reviewed in Spain on September 9, 2013
Buenos dias,Siendo cliente habitual de Amazon,con varios pedidos realizados correctamente, me encuentro al recibir este pedido que la descripción es totalmente confusa.Tanto la foto como la descripción indican que se trata de un candado, al recibirlo veo que es sólo la funda plástica de color morado.Procedo a la devolución del mismo, reviso en mi cuenta de amazon en el apartado de devoluciones,y pone que se ha procedido ya a la devolucion al vendedor, pero no dejo de recibir correos electronicos de Amazon recordandome que debo proceder a la devolución.Ya está realizada,tal y como aparece en mi cuenta de Amazon,y no encuentro ningún correo electrónico al que dirigirme,ya que si intento contestar al que me envían notifica error.Ruego revisen el tema porque ya he procedido a la devolución, y sería conveniente revisar la foto y descripción del producto porque no se corresponde con la mercancía y es normal que de lugar a errores,y a decepciones con Amazon de clientes que durante años hemos comprado productos y estabamos altamente satisfechos. Ruego revisen mi historial o me faciliten un correo electronico para explicar lo sucedido y que se solucione lo antes posible.Saludos
MANUEL ROBERTO CASTAN MARCOS
Reviewed in Spain on September 10, 2013
Lo compré pensando que era un candado como indica su descripción principal y es una funda.Lo he devuelto. Ahora a ver cuando lo pagan.
JennieJump
Reviewed in the United Kingdom on March 2, 2013
This is a great idea for a lock which previously was a disgusting orange!I was guided by the instructions written in a recent review of this product on amazon.com. In other words, just follow the basic manufacturers instructions, without the bits which are added in case the skin doesn't go on correctly. It all went on like a dream (and like a previous reviewer, I am a woman, and not a whiz at DIY or anything), and I thought it was going to be so difficult. As long as you use washing up liquid it's all very straightforward.And it looks really great on my bike!
Borghold
Reviewed in Germany on April 6, 2013
Sehr schön, dass man mit dieser (farblichen) Hülle endlich die Möglichkeit hat, die Befestigung für die Rahmenhalterung (wenn man diese - wie ich - nicht nutzt) kpl. zu demontieren. Das Befestigungsteil (im Produktbild: der metallene, silberne Adapter) barg stets die Möglichkeit des Lackschadens am Rad.Und da der gelieferte Schlauch für den Bügel lang genug ist, kann man diesen kpl. über den vom Befestigungsadapter befreiten Bügel schieben. Perfekt! Den Befestigungsadaper entfernt man schlicht mit einem Inbusschlüssel.Lange gesucht - jetzt gefunden: die Lösung für dieses "Problem". Kaufempfehlung.
missE
Reviewed in the United States on August 6, 2012
Product looks great once it's on there. I generally followed the instructions and would mention these three things.1) I had a really hard time removing the old vinyl (orange) cover from the crossbar. Some reviewers mentioned this was easy to wiggle off, but not for me on my mini-Evolution. A stronger (male) friend was finally able to pull it off for me after we soaked that end of the crossbar in hot water for a few minutes. I suppose I could have cut it, but I was trying to keep it in one piece in case I had to put it back on.2) After letting both the new vinyl tube and bare shackle pieces soak in hot water for 5-10 minutes (instead of their recommended 2-3 minutes), I used regular Dial hand soap to coat the shackle part. The important part in putting the new vinyl tube on was keeping my hands and the vinyl dry so that I could get a good grip on it. As long as I had a grip, it would slide pretty easy. I DID NOT use an air gun or any special lube and once everything was soaked in hot water, putting on the new vinyl tube took less than 5 minutes.My advice on this step since it seemed to get the most comments from other reviewers:-Have a towel handy-Let both the new vinyl tube and bare shackle pieces soak in hot water for 5-10 minutes-Coat about 2/3 of the shackle generously with soap - starting with the straight leg and continuing up around the top of the "n" (I used regular Dial hand soap and starting with the straight leg means there's one less curve for the new vinyl tube to have to slide over)-Dry your hands-Dry the outside of the warm vinyl tube (you won't get anywhere if you can't get a good grip on it)-Hold the non-soapy leg of shackle with ONE hand-Grab vinyl tube with other hand and start sliding it over the soapy leg of shackle-About 2/3 of the way through when the new vinyl tube has covered most of the soapy part, stop-Now put soap on the remaining exposed part of the shackle and set shackle down-Dry both hands again-With one hand, grab hold of the shackle in a spot where it is covered with the new tube and continue sliding the tube, only this time rest the bottoms of the shackle against the counter or something so that you only have to use one hand to do the sliding and not interfere with the soap3) I ordered the white skin. It was hard to tell from the picture, but the dust cover that comes with the white skin is clear colored. This means that when it's on the crossbar, it appears black. I wish it was white or silver colored.
JOHN F. CAMP
Reviewed in the United States on June 30, 2011
I BOUGHT THESE TO REPLACE THE EXISTING COVER ON MY KRYPTONITE LOCK, BUT IT IS ALMOST IMPOSSIBLE TO REMOVE THE EXISTING COVER AND PUT THIS PRODUCT ON. I DO NOT RECOMMEND PURCHASING THIS ITEM!
esqgirl
Reviewed in the United States on June 16, 2011
I got this for my new mini-u lock, to help it match my bike, and to distinguish it from my sweetie's when we grab them from the bike shed. One of the reviews here made me a bit nervous that it would be a pain to install, so I wanted to come back and report. I think the manufacturer's instructions might make it seems a little more complicated than it really is, as they cover a lot of contingencies and have hints you might not need. Basically:1. Easily wiggle off the pieces on the crossbar and replace with those provided. There is no real resistance or difficulty with this part.2. Remove the two rubber gaskets and the hanging mount if you have one from the u-shaped part of the lock.3. Cut off the vinyl cover on the u-shaped part of the lock. They suggest heating the metal and existing vinyl cover in hot water first, to make it pliable enough to fit scissors under the edge, but it was easier to just carefully use a box cutter.4. Adjust the size of the replacement vinyl cover per the directions to roughly match your lock size (you will do final trimming later)5. Heat the metal and the new vinyl in hot water for 2-3 minutes to make things easier (this time it is necessary); put a spoonful of dish detergent in your hand and coat the u-shape; dry your hands for traction.6. Quickly slip the new vinyl over the metal, scooting it along until it is in place. Using a cloth for traction helped. There will be some extra on both ends. This is the step others seem to have had trouble with. It took me about 90 seconds. I think it would have been much messier if I had used actual bike lube. The directions include a bunch of hints, and how to get it started again if the vinyl loses pliability before you get it all the way on, like re-warming and re-lubing, or using an air gun. They also mention a YouTube video, but I did not need to refer to it.7. Trim the ends of the vinyl to the right length specified in the directions, and replace the rubber gaskets and hanging mount.The whole thing took about 15 or 20 minutes, including reading directions and all set up and clean up. I really like the new look. Good luck!
Recommended Products
