Your cart is empty.
Your cart is empty.Product Description
Neoteck 0-1'' Dial Table Saw Gauge Set for Aligning and Calibrating Work!
Neoteck table saw dial indicator is designed according to standard miter slot size (3/8 "x 3/4"), and it can test your table saw, fence alignment & position problems. Table saw gauge can check arbor & blade run-out, miter slot to blade squareness or any other alignment measurement.
The measurement range of the table saw gauge is 0 ~ 1 " and the high resolution up to 0.001 ", which can reduce the measurement error. Neoteck table saw dial indicator is clear and easy to read, which helps you get the measurement results quickly and accurately, so that you can do your job better.
The 18cm anodized aluminum bar of table saw gauge adopts three chute design, ensuring the hardness & applicability of the bar. (Aluminum alloy bar is suitable for table saw with groove width above 1.9cm, if groove width is greater than 1.9cm, it can be adjusted by screws)
The anodized aluminum rod of the table saw gauge is machined by CNC with accuracy of 0.02mm, which reduces the gap loosening after the aluminum alloy rod is fixed and does not shake after installation as well as reducing wear, preventing rust and extending working time.
This accurate and professional table saw gauge can be widely used in calibration work, shop machinery, band saws and drilling machines. It is a -must-have tool for your tool box!
Package includes: 1 x Dail Indicator, 1*Chute Rod: L155 x 19 x 9.3mm (6.1 x 0.75 x 0.37 inch）,1*Dial Gauge Rod: L180 x W19 x H19mm (7 x 0.75 x 0.75 inch),2*Springs ,6*Screws,2*Metal Gaskets,2*Hex Key.
Dazed and confused
Reviewed in the United States on March 29, 2025
Knob screws did not fit threaded holes in bar. Washers too small to accept smaller screws. Allen slot in smallest set screw did not fit supplied hex key. So half the things that were supposed to fit did not. Pretty shabby quality. No idea how the dial feeler gauge works yet. Not optimistic.
Kat
Reviewed in the United States on March 28, 2025
Product is well built, however the piece that fits inside the saw track is too thin and will not lock into the piece with the gauge. There are riser screws, but the pins in the bar that runs in the track will not stay in the track. Not the best design...
Walter
Reviewed in the United States on February 11, 2025
Table saw gauge seems to work well, but the two springs were to short for my Ridgid table saw.
Samantha
Reviewed in Canada on January 18, 2025
I used this to check my Dewalt 10" table saw... I was amazed at how accurate my table saw was. There are great videos on-line to help with using the product. It did the job for me, and I will loan it to friends for same purpose.
Robert P.
Reviewed in the United States on April 8, 2025
It takes a bit of fiddling to get the bar adjusted tight. I used a tiny strip of Teflon tape on the threads of the set screws to keep them adjusted. The threads were a bit loose. Other than that, really nicely made product.
Customer
Reviewed in the United States on April 4, 2025
Great tool. I thought I was just a crappy craftsman, but now I know my saw blade is warped.
Andre Fortier
Reviewed in Canada on April 1, 2025
Précise and exactly as it is shown
Raul Zuniga
Reviewed in the United States on August 25, 2024
Faulty threadVery good product, a firm structure, easy to assemble and use. The calibration of my cutting table was fast and accurate in the calibration of the cutting blade and the fence.I give this product 4 stars only because one of the screws came with a damaged thread and I had to replace it with another screw that I had available.
PK@CA
Reviewed in Canada on August 22, 2024
I'm using this for an older metal lathe to zero out the cross feed. Overall, the build quality is excellent, although not perfect. The quality of the dial is very good, but not high-end. As a table saw gauge, it would be ideal for someone new to setting up a table saw. The directions will be lacking, but for somebody with a little bit of experience setting up a table saw, it'll be adequate.If you're looking for perfection, this is a 9 out of 10. It is well-made and fairly priced.
AMac
Reviewed in Canada on August 14, 2024
This product worked as advertised and helped me dial in my General cabinet saw. It is critical to have your blade true to the channels for the cross-cut sled and also true to the rip fence to prevent kickbacks or burning of the wood. I first aligned my blade to the Mitre gauge slot and then aligned my fence to that. It is also recommended to periodically check this, as things do move and change due to temperature fluctuation.This product was well-built and reasonably priced. I am used to using these in the past so setup was easy .. lots of YouTube videos out there on how to use these
Franco
Reviewed in the United States on July 28, 2024
I'm a hobbyist woodworker, and I've always just used a standard machinist square to make sure my table saw blade was square to my table and miter slots, but this gauge really helped me dial things in perfectly.First of all, the aluminum bars are solid and feel weighty and durable. Putting the gauge together takes no time at all, but dialing it in to calibrate your blade is a bit tedious. The plunger screws can be adjusted to fit your miter slot, but dialing them in perfectly takes a while. Similarly, the star nuts used to level the bar need a lot of finessing to get them to sit right as well. But once everything is set up, the gauge is incredibly sensitive to even the tiniest differences across your blade, so you can see exactly how your blade shifts in relation to your miter slot.Overall, I'm really pleased with the quality and precision offered by this gauge.
John
Reviewed in the United States on July 17, 2024
This indicator is very sensitive and very easy to use. The indicator uses the table slots resident on your tool tables to assist alignment with various cutting tooling. The aluminum slot bar is adjustable to fit as needed to various slot sizes or alignment tabs via set screws with the crossbar being anchored in a defined groove via a thumb screw.After using this easy to read dial indicator I was pleasantly surprised to find my table saw - dead on but I had an issue with my band saw that I was not aware of. Now after using this alignment tool my wide metal blades are tracking parallel to the slots.For m the only downside is there was no protective case provided to secure an item that should not be jogged about.
Guy
Reviewed in Canada on November 21, 2024
I will return this product as it does not fit properly on my table saw.
Recommended Products