Your cart is empty.
Your cart is empty.Product Description
Importance Note：
✔ For Ender 3, you just plug in and start printing.
✔ For Ender 3 v2/ Ender 3 pro/ Ender 3 Max/ Ender 3 Neo/Ender 3 V2 Neo/Ender 3 Max Neo, please update firmware. DO NOT TRY RANDOMLY.
✔If you have any other issues with the firmware updating, you can refer to the firmware flash videos available on our product page.
Product Specifications
- Version: V4.2.7
- Voltage: 24V Input/12V Output
- Firmware: V0.0.6/V1.0.6 based on Marlin 2.0.1
- Motor Driver Stepper: TMC2225
- TMC2225 drivers, Marlin 2.0.1 and bootloader has been pre-installed.
Timothy McNabb
Reviewed in the United States on January 25, 2025
I had the 4.2.2 board shoot craps, so I ordered this as a replacement/upgrade along with the CR-Touch. It is an intermediate-level effort. On my unit, plugs had some hot glue on them to hold them in place. I used a syringe with a bit of rubbing alcohol to break the hot-glue bod with the plastic and it picked right off.Switch one plug and one wire at a time. Be patient, and watch a couple YouTube videos.
Michael Wilson
Reviewed in the United States on January 21, 2025
I had accidentally damaged the micro USB port on the original board for my Ender 3 V2. Rather than trying to replace the port, I figured I’d get this as an upgrade. It has worked well for me so far. The noise from the motors are almost non existent, which is fantastic. The only noise from the printer are the fans. Creality’s installation tutorial was clear enough for me and there are also plenty of other guides out there too. Just be warned that it does take some time to swap out. I can confirm it works with the mriscoc firmware as well if you are inclined to use that.
Conor Hildebrandt
Reviewed in Canada on January 11, 2025
If you have an Ender 3 and have to listen to it get this upgrade immediately. The difference is insane and it's so nice to have such a quiet machine. I'd never buy another Ender 3 again but if I did I would get another one of these boards
Steve
Reviewed in the United States on April 24, 2025
Went in with no issues. Did the firmware update, had to do the Hot End PID calibrations, reset all the E-Steps, and since I also added a probe, I needed to set up the X and Y offsets. Worked awesome. Quiet and prints look a lot smoother. This is something that should be updated on an old printer like my Ender 3 V1. The prints I'm getting now are as good as my new Ender 3 V3 Plus.
Marco Aurelio Rendon Medina
Reviewed in Mexico on April 19, 2025
Hola es una gran mother board, solo deben tener en cuenta a qué impresora se la van a poner .Yo la usé en mi ender 3 pro. Viene precargada con laEnder 5. Entonces es necesario ir a la página de creality bajar el archivo frimware correcto y poner el archivo bin en una sd card. Después introducirlo con la impresora apagada y prenderla para que se instale el frimware marlin 2 correcto.Espero a alguien le sirva por que yo me tarde mucho tiempo en resolver este problema. El cubo azul es con el frimware que viene preinstalado y el gris es después de hacer todo el proceso . Espero les sirva
Scrimshaw
Reviewed in the United States on May 23, 2024
I got this board installed easily enough on my (1st generation) Ender 3 Pro by following some online video tutorials. The biggest challenge was the old board had all of the connectors hot-glued, so I had to peel off a lot of glue to release the connectors from the old board. However, once that was done, this was fairly straightforward to install.I was also installing a BL touch at the same time, and I wasn't sure if the firmware on the board would support it out of the box, so I downloaded the appropriate code from the Creality website. The most current code I could find on their website for this V4.2.7 board (that supported BL touch) was Marlin V2.0.6 (under the basic Ender 3 section, not the Ender 3 Pro section).The only odd thing I've noticed is that when it's auto-leveling with the BL Touch, this board intermittently turns off the hot end, so it cools while leveling, and then you get a thermal error about 10 seconds into the print because the nozzle is too cold. I have searched online for an answer to this, and haven't found the "right" answer (to keep the hot end turned on during leveling), but did find a work around by adding an M109 command to my startup Gcode, to force the hot end to heat up again. I wish Creality kept their code more current, so hopefully this helps you if you encounter this problem with this board.Overall, I love this board. It's super silent, and the only noise is the fan. Rarely you can hear a bit of stepper noise (just barely) for a moment when it's printing an interesting curve, but that's it. Even with Creality's outdated firmware, I'm giving this 5 stars.
Miguelonmex
Reviewed in Mexico on December 13, 2024
Éso si, tuve que flashear el firmware para que quedara como a mi me gusta.Y si es silencioso a comparación de la tarjeta original de mi Ender 3 pro.
Eric A
Reviewed in the United States on October 8, 2024
Well now Ive upgraded just about everything on my ender 3 because of this board. Good money grab there Creality! Anyway, I changed the board to this one from 422, kept getting runaway, changed the entire hot end, still getting runaway, went to marlin updated firmware, got rid of the runaway, but the cr touch wouldnt level, tried different firmware, now bed heat error. Changed hotplate, still hot bed error, try different firmware again, after quite a few different flavors I got one that doesnt give heat errors but....... it lockes up while printing which makes it impossible to fine tune. It locks up as if its busy thinking, then it unfreezes and jumps menus. All I want is for it to work.. going to return and toss 4.2.2 back in and see what I can do. I like a challenge but this is ridiculous!
luis fernando
Reviewed in Mexico on October 18, 2024
Excelente, funciona perfectamente y no hace ruido, aunque me lleve un pequeño susto cuando la instalé, el pequeño ventilador no giraba cuando hice la prueba, era porque tenías que ponerle manualmente las revoluciones si lo querías probar, todo lo demás bien.
BrokenCinder3
Reviewed in Canada on September 19, 2023
I just got finished installing it and have only run a couple very short prints but I’ve been doing a bunch of upgrades to my Ender 3 and this is for sure one of if not the best one I’ve done so far. It makes the motors whisper quiet and I needed a new board anyway because when I was doing some other work I accidentally fried something in the other one so that the centrifugal fans would never kick in. Oops right. Also I don’t know if it’s just upgraded firmware or something you can only get on a different board but it has a different version of the firmware on it and it has a different layout with more features which is super nice. And also I’m hoping this one won’t have some of the glitches the original board had as I haven’t had any come up yet where it would on the original. One thing to keep in mind is they don’t send very good instructions for swapping over but if you’re at this point of messing with your printer I’m sure you have a good enough understanding of it to do everything. And if you’re nervous just take pictures and mark where things go. It is just a plug and play swap. Overall great upgrade and highly recommend.
C Dow
Reviewed in the United States on January 23, 2023
The media could not be loaded.
Recommended Products