This pipe table leg set was great. It's real steel pipe like from the hardware store. It does have a layer of oil on it so that must be stripped using dawn or some other degreaser before handleing and painting. It is also offset in the middle bar so if you use it as a desk you get more leg clearance. I used it as a table base so I bought matching middle braces to set the middle support in the center of the table. Once together it looks great. I highly recommend getting this if you want a good quality pipe base.

Purchased two sets to create a custom L shaped desk for the office. Placed a pine stained top. Perfect to handle a monitor, multiple laptops, normal office equipment. Extra benefit is the cross piece at the bottom as a foot rest. Very sturdy while sitting on carpet. Compared to normal pipe material purchased in large box store -- could not have asked for a better product for the price. Looking at other products for additional projects for around the house for the product and vendor. - Highly Recommend.

These legs are great. I put it together with a butcher block tabletop and it turned out beautifully. I recommend using a level on the legs once you get them into position and again when you place a top on it. The screws included were so easy to screw into the block but that will vary depending on the top you select. Watch the videos another reviewer posted on cleaning the legs with a mild soapy water and dry them thoroughly. It really helped me. Also after it was all assembled I used a clear acrylic - in a spray can to clear coat and seal the legs. I am really happy with it.

Easy to assemble, all the pieces were in the box. I set everything out to be sure. Instructions were easy and clear, took about 10 min to put together.Seems to be quality pipe, strong stable build even at just hand tight. When I put the desk top on it was already level so bonus there.This kit is a great value, before I found the M desk I was looking on Pinterest for pipe leg designs thinking a trip to the hardware store and I could make it for cheaper, which was not the case. I 100% will recommend, and will purchase again.

Put this together in about April 2020 right about the crazy lockdown/quarantine/work-from-home timeframe. I knew that I wanted a simple hardwood desk with no drawers or stuff below the top. I have an ergonomic keyboard tray that I have attached to all my work desks for many years now, and it was too long for my old home desk, which was also made of MDF and was falling apart. Boo.Enter this kit plus a butcher block top from the big box store. This kit went together easily. I had lost the instructions but a quick email to the JS Supplies company, and they hooked me up. By the time they sent it, I had actually figured out the part that was puzzling, which was what the all-thread pieces were for (the couplers between the elbows and the flanges on the top side).I degreased all the parts with a simple Simple Green-type solution diluted in a 5 gallon bucket. I then sprayed the pieces with a satin nitrocellulose laqcuer (Minwax brand that I got from the home improvement big box). Worked great. I thought about doing a sealed rust finish using a science project volcano--vinegar and baking soda for a quick layer of rust on the outside--but I decided against it, as I wasn't sure of how stable the final product would be, even after a clear spray finish. The satin nitro finish looks great without even looking like a finish. I also coated the pieces with paste wax after the finish dried, just for good measure.The one thing that is a bit disappointing is the stability... WITH MY TOP, mind you.I should be clear that the top that I'm using is a 1-3/4" thick monster piece of birch butcher block that is 60" x 30". I'm guessing that it's 40-50 pounds? Maybe more. This is probably WAY more weight than this leg set is made for. I also have the aforementioned keyboard tray that sticks out (torque equals force times lever arm) and causes even more torque. I get some shaking with the top with this setup. I have the desk on carpet; I was concerned that maybe the carpet and pad were not giving enough stability with the feet, so I made some plywood platforms for the feet. I also carefully leveled the feet to make sure it wasn't just uneven legs that was causing the instability. Still shakes no matter what I tried.I think it's just that I have such a heavy top--more than this thing is spec'd for. That's totally fine, and I don't want to knock off a bunch of stars for that. I leave these comments more as a "don't do what I did" thing. Just be advised that you need to limit the weight of the top to something reasonable.The design of one upright on each side of the desk with a pipe coupler in between is probably the weak spot with my heavy desktop; I'm thinking of either adding tension on either side (with some threaded rod and turnbuckles) or some extra supports with something like the Steel-Tek pieces from Lowe's.Overall, I'm very satisfied with the product and the company!

For starters, this is a great buy if it is exactly what you want. For me that was the case and it would have cost me a good $40 or more to replicate it at a big box store. With that said, if you are not planning on using all of the pieces and want a different configuration, this may not be the kit for you. All of the parts inside are just like if you bought it at a local home improvement store. All the pipes need to be cleaned and protected. I personally found that dish soap (dry off immediately after you clean a piece) was the easiest to clean everything and I finished it with some wax. The kit is sturdy and easily supports the weight of my butcher block tops. I inverted the kit as it is designed as I intend on adding a shelf and am planning on using the support brace to aid in holding that shelf up for cable management. After cleaning and protecting, putting the kit together only took 5-10 minutes and that was with kid disruptions. I purchased 2 so that my wife and I could have matching desks in the office and I couldn't be happier.

Definitely thankful I came across these legs. I had an extra bamboo table top and needed legs for it. However I wanted it to have some character and these pipe legs worked perfectly. I will say, cleaning off the oil and sealing the iron is a bit of a project -- but I just threw on a podcast and enjoyed the process. Easy to assemble and customizable. This basically saves a newbie like me from walking into home depot like a lost duck trying to piece together the right materials. Thanks again. I have two more table tops and will likely buy again the future!