Your cart is empty.
Your cart is empty. This keypad will work on models ED2 and the FD units. These keypads are sun and weather resistant and uses the best adhesive for sticking to your heaters bezel.You will peal off the off the old keypad and stick this one on in its place. This is a very easy DIY project. In less than 10 minutes you can have a new keypad and a working heater again.
work with:
FITS ALL H SERIES, H SERIES LOW NOX AND UNIVERSAL H SERIES LOW NOX HEATERS.
gary dority
Reviewed in the United States on June 13, 2024
Looked and fit perfectly,quality materials and 3m replacement peel off on back hold very well.Downside.. replaced this last year around the same time. Only lasted a year, which is four months in pool years.
Customer
Reviewed in the United States on March 30, 2024
My keys on my Hayward H250ED2 were intermittent at best. Replaced the membrane keypad with this and it works perfectly. Doesn't say Hayward on it but then I don't really care about that. Not hard to disassemble the unit. All you need is a Phillips head screw driver.
Paul Betts
Reviewed in the United States on December 22, 2023
Assumed I needed a new pool heater when I saw the error code, but was hopeful after searching internet for possible solutions. This very cost effective and easy to install product did the trick.
Michelle B.
Reviewed in the United States on May 30, 2022
Called 5 pool stores/service providers, no one carries this part. Ordered Saturday received earlier than expected 2 days later-on Memorial Day. Installed in 10 minutes, works great. Cannot comment on longevity yet but I can heat my pool again for less than thirty dollars so I am VERY happy. Thank you for supplying this part at a fair price, easy diy fix, no need to wait for service and pay excessive fees. (Hayward h200 pool heater)
bailey2408
Reviewed in the United States on November 13, 2022
Didnt want to spend over 200 for a whole bezel replacement and stumbled on this. Watched youtube vid on install and only took 10 minutes to install! Now get to use hot tub again after years of putting it off. Works like original! Time will tell about longevity but for now im a happy customer!
Rolo Tutor
Reviewed in the United States on June 9, 2021
Easy Install and Fits Great. Took me about 5 mins. Works really well.
Mike
Reviewed in the United States on October 26, 2021
I bought this plate even though it didn't match the old part's graphics perfectly. I have some experience working on my pool heater from before but wasnt sure if this $20+ part was going to solve the problem (increase temp button wasn't working). A couple screws later and with some basic understanding, the heater is working perfectly again. Thanks so much!
Spyridoula Iliadis
Reviewed in the United States on May 18, 2020
I used this to replace a worn-out display panel for a Hayward H400 heater. There were no instructions that came with the unit but I was able to find a YouTube video that was helpful. Most reviews say "Peel 'n Stick" and you are done in 10 minutes but it's not quite that simple! It took me about an hour to replace but I took my time, so I figured I would write this review to help out any other buyers. Disconnect power from the unit beffore you start. First you have to remove the unit from the heater by carefully disconnecting the 3 plug-in connectors (note orientation) and a sensor. Then, the unit can be separated from the heater. Take the metal shield off by removing the 3 screws. Remove the unit from the face plate by removing the 4 metal screws in the front. Remove the back plastic cover by removing the 2 screws. Finally, loosen the circuit board by removing two screws. Note the ribbon connector on the circuit panel that connects to the display panel. Carefully peel the old display board and disconnect the ribbon connector. There is a small display panel in the middle of the board that may need to be loosened by releasing the 4 small plastic tabs. Clean the face of the panel and peel/stick the new board making sure the holes lineup with the display openings. Plug in the ribbon connector. Snap in the small display panel in the middle of the circuit board. Secure the circuit board, install the plastic cover and install it back on the metal face plate using the 4 sheet metal screws. Reinstall the heat shield. Finally, carefully connect the plug in connectors and the sensor input on the unit. Turn power back on and hopefully you can enjoy the heater again!. As you can see, it's a bit more involved but very doable with a bit of patience. Hope this helps !
Recommended Products
$37.23
$ 19 .99 $19.99
$68.99
$ 28 .99 $28.99
$55.76
$ 29 .99 $29.99