Your cart is empty.
Your cart is empty.Product Description
SPECIFICATION
- Base Type: 1142 BA15D 1076 1004
- Luminous Flux: 500lum
- Power: 3W/Bulb
- Voltage: 12V DC
- Color: White 6000k
- Size: 1.69" * 0.75" (43mm*19mm)
- Packaging: Pack of 10 1076 led bulb
- LED Type: 5050 27SMD
SEVERAL ADVANTAGES WORTH YOUR CHOICE TO BUY:
Fits 1142 1004 BA15D 1076 #90 #68 socket
- Standard 1142 1076 BA15D socket, copper and iron head, not easy to deformation
- Direct replacement for the 1142 1076 light bulbs in a light fixture
- These 1076 led bulbs for rv don't get overly hot. Nicely and safely packaged
- Energy-efficient, low power consumption. The service life is more than 10,000 hours
- The 6000K white color temperature of these 1142 led bulbs are close match for the incandescent lamps in your RV
USE FOR RV INTERIOR LED LIGHT
- Camper Trailer light
- RV Wall sconces
- Interior RV light bulb
- Motorhome living room sconce light
- Sailboat interior Light
- Ceiling dome light
- 5th Wheel interior lights
- Deck lighting
USE FOR CAR LED LIGHT
- Map light
- Ceiling Dome light
- License Plate Light
- Luggage light
- Reading Light
USE FOR HOUSEHOLD LIGHTS
- Lawn Lamp
- Bedside Reading Lamp
SOME COMMON QUESTIONS
- Q: Why don't these bulbs light up when plugged into a socket?
A: These 1004 led bulbs are polarity sensitive, if your 1004 led bulb's top central pin is "- polarity", so these 1004 bulbs are not suitable, you may need a Non-Polarity led bulbs.
- Q: Why do I plug into the socket it is very loose and does not seem to fit my socket?
A: If the original bulb top contact is high, it is recommended to use solder to make the contact point higher, otherwise poor contact will occur. This is not a quality problem of the bulb itself.
- Q: After I install this LED bulb, the bulb will Fast Hyper Flash or the dashboard will display an error message, how do I fix it?
A: You need to install an additional 50W 6ohm load resistor(ASIN: B07FB2KJGH ) or LED Decoder
THE SOLUTION OF BULB NOT LIGHT UP:
First: the bulb is a polarity required bulb. This means that the contacts inside the socket are only designed to work one way. So, if you put the bulb in and it doesn't work, take it out, turn it 180 degrees and put it in that way. The polarity must be right or you don't get light.
Second: the socket must be able to make contact with the bulb. In my sockets, the metal contacts in the socket were pushed down over time from use. The pictures are as clear as I can get but you'll see the one picture where the contacts are actually bend inward, away, sunk in. Make sure the switch is off and gently bend them back up a bit so they're no longer bent in but instead level or slightly up (just slightly). Then try the LED again.
Please find out the correct model you need before you buy, this is the difference between the three models
1141 BA15S Base
- single Contact on the bottom
- The pins on side are at the same levels not staggered，pins in 180 degree at same level
1142 BA15D Base(This product is this Base)
- Double Contact on the bottom
- The pins on side are at the same levels not staggered，pins in 180 degree at same level
1157 BAY15D Base
- Double Contact on the bottom
- The pins on side are not at the same levels not staggered，pins in 180 degree at not same level
Ann
Reviewed in the United States on February 5, 2025
Got these to replace bulbs In older fleetwood and look great. Easy to install. Color is good
Rolle
Reviewed in Sweden on September 18, 2024
Lyser fint
DCRM
Reviewed in Spain on March 28, 2024
LAS BOMBILLAS FUNCIONAN CORRECTAMENTE, SIN EMBARGO EL TESTIGO DE FALLO SALTA EN EL SALPICADERO.
Customer
Reviewed in the United Kingdom on December 8, 2024
quick delivery nice products
Fran
Reviewed in Spain on September 12, 2023
Perfecto
KN4REN. RON
Reviewed in the United States on February 10, 2023
Using in camper the LED Lighting up dating my camper reduced the strain on my battery and Greatly improve the internal and external lighting om my camper , easy to replace
Customer
Reviewed in the United States on December 1, 2023
This is my second batch as I ran out converting all boat light to led... Work good
Velaraf
Reviewed in Italy on April 27, 2021
Attese sodfisfatte
crasagam
Reviewed in the United States on August 15, 2020
These are plug-n-play as long as they work. But when they don't you need to be smarter than the bulb.First: the bulb is a polarity required bulb. This means that the contacts inside the socket are only designed to work one way. So, if you put the bulb in and it doesn't work, take it out, turn it 180 degrees and put it in that way. The polarity must be right or you don't get light.Second: the socket must be able to make contact with the bulb. In my sockets, the metal contacts in the socket were pushed down over time from use. The pictures are as clear as I can get but you'll see the one picture where the contacts are actually bend inward, away, sunk in. Make sure the switch is off and gently bend them back up a bit so they're no longer bent in but instead level or slightly up (just slightly). Then try the LED again.In EVERY one of my sockets one or the other of the two repairs above brought the LED to life. My camper looks great now and I've ordered more to finish replacing the rest of the lights.
Andrew R.
Reviewed in the United States on July 21, 2020
So far they work great and were a good price!Though 4 of the bulbs didn’t light up.
Unrealbullet
Reviewed in the United States on February 6, 2020
Didn't even work when plugged in.
Andrew
Reviewed in the United States on April 18, 2020
They're nice bulbs one out of the 10 did not work they are bright white very bright and not as soft white but they appear to be good quality will see fast shipping though great price
Chad
Reviewed in the United States on July 19, 2019
Be sure you know if you have a single or dual contact bayonet. I ordered the dual and need single and missed the return window. The bulbs seem like they are very good quality.
Recommended Products