Nema23 Stepper Motor 270Oz-in

• Motor Type: Hybrid Stepper
• Phase: 2 phase
• Step Angle: 1.8 degree±5%
• Voltage: 4.8V
• Holding Torque: 180N.cm(270oz-in)
• Detent Torque: 6N.cm Max
• Rotor inertia: 440g.cm²
• Phase Resistance: 1ohms
• Insultaion Class: B
• Inductance: 3.5mH+/-20%(1KHz)

TB6600 Stepper Motor Driver Features

• Original brand new stepper motor driver chip
• 8-speed current control
• 7 kinds of subdivision adjustable
• Interface uses high-speed optical coupling
• Automatic half flow reduces calorific value
• Large area heat sink is not afraid of constant high temperature environment
• Strong anti-high frequency interference
• Input voltage anti-reverse protection
• Overheat and overcurrent short circuit protection
• Through the 3-digit dialing code, you can choose 7-step subdivision control (1, 2 / A, 2 / B, 4, 8, 16, 32), 8-step current control (0.5A, 1.0 A, 1.5A, 2.0A, 2.5A, 3.0A).

Mach3 USB Motion Control Board 4-axis

• Maximum step-pulse frequency is 100KHz,which is suitable for the servo or stepping motor.
• Need use external 24V DC power supply to isolate USB and external port, and to make the system more stable.
• 4 general-purpose inputs, you can connect the limit switch, estop switch, probe switch, back to zero and other device.
• 4 general-purpose isolated relay drive output interface, can drive four relays for controlling the spindle starts, forward rotating and reverse rotating, pumps and other device.

350W 24V DC Switching Power Supply

• DC output: 24V 0-14.5A
• Inlet stability: ±0.5%
• Load stability: ±0.5%
• DC voltage of Adjustable range: ±10%
• AC input voltage range: 115VAC/6.5A/50HZ----230VAC/3.4A/60HZ; Selected by switch
• Overload protection: 105%-135% cut off the output, automatic recovery
• Over-voltage Protection: 115%-150% shut down O/P voltage, re-power on to recover
• Setup/rise/hold-up time: 200ms、50ms、20ms/230VAC at full load
• Withstand voltage: I/P-O/P: 1.5KvAC; I/P-FG: 1.5KvAC; O/P-FG: 1.5KvAC; 1minute
• Isolation resistance: I/P-O/P、 I/P-FG、O/P-FG: 500VDC/100MΩ

How to connect the Tb6600 driver ( or Stepper Motor) to CNC Motion Control Card?

• It should be noted that the wiring diagram of the 4-axis motion control card above is for reference only, then if you connect this control card and the TB6600 driver, such as connect to X-axis motor driver, then:

1. Driver's "Pul+" connects to control card's XP+ pin ,
2. Driver's "DIR+" connects to control card's XD+ pin ,
3. Driver's " PUL- " pin and " DIR- " connection to USB Mach3 control card's " GND "

• Stepper motor's wrings ( 4 wires) :

1. Connect stepper motor's RED wire to driver's A+ port
2. Connect stepper motor's GREEN wire to driver's A- port
3. Connect stepper motor's YELLOW wire to driver's B+ port
4. Connect stepper motor's BLUE wire to driver's B- port

Package Include:

• 3 × Nema23 Stepper Motor 57mm
• 3 × TB6600 Stepper Motor Driver
• 1 × Mach3 USB CNC Control Card+USB Cable
• 1 × DC Switching Power Supply

• 1 status LED, indicate connection status on the board.
• Have 0-10V output port, you can use mach3 software to control the spindle motor speed.
• Support for 4-axis linkage, you can connect four stepper motor drives or servo drives.

• Support automatic probe tool
• Support Emergency input
• Support for limit switch (It is recommended that the limit switch and emergency stop switch must be installed first and can be used normally.)
• Support for connecting electronic handwheel

• This USB motion card does not need install any USB driver, Windows2000/XP/Windows7,can directly identify (Notice: Doesn't support Win8/win10/macOS system !!!) .
• If you are not familiar with the product and software features, make sure the machine's power switch on hand, you can quickly turn off the power.
• Recommends that users install the emergency stop button and make sure the button is functioning properly.

Multiple protection, Stable Performance

• Short circuit protection: when the output terminal is short-circuited, the power supply turns off the output, and the output voltage is 0V.
• Overcurrent protection: When the output current>115-150%, the output voltage turns off the output.
• Overload Protection: Power protection when load power＞105-135% of rated power.
• Temperature protection; the power supply is automatically protected at high temperatures.

Double Ball Cooling Fan and Full Metal Housing Design

• With high speed and quite characteristics, it can ensure the temperature operation of the equipment and extend the service.
• The shell is made of aluminum alloy with high thermal conductivity system, which is reinforced and durable, and the design is more user-friendly.

Input Voltage Switch

• The power supply has an input voltage 110V-220V switch button, which can adapt to different voltage requirement.
• Quadruple protection setting, high resistant to electricity, effectively reducing the impact of AC input.