Your cart is empty.
Your cart is empty.PLEASE make sure you have the right barrel. Prommy makes many kinds of AEG barrels. This R-hop ONLY fits the KRYTAC Barrels with the 2x Sloped cuts. Not others. These who have other Prommy barrels that are DIFFERENT from the KRYTAC barrels bought this R-Hop, and of course it did not fit. If you have a different Prommy barrel, such as the EG, EMG, VSR, these R-Hops are in seperate listings. Features: R-Hop is the single most important part in airsoft that extends your effective range to over 60m/200ft. Max range of 90m/300ft can be achieved (with M130 spring, 1.7J). PERFECTLY Fits Prometheus 6.03 Krytac Tight bore barrel. NO SANDING is NEEDED. This R-Hop is Extremely hard to fabricate due to the 2X 101.5 degree cuts. We are the only aliens on this planet who can cut it accurately, repeatedly. Traditional R-Hops are 1.5mm thick and airsoft barrels are 1.25mm thick. Thus, sanding is required. Our R-Hops are Exactly 1.25mm thick. Therefore, NO SANDING is required. Made of Premium-Grade Silicone Rubber, to produce MAX spin. Cold weather resistant. Proudly Made in USA.
Warren A. Wilson III
Reviewed in the United States on July 14, 2023
Followed the directions installing it. A small roll of a paper towels in the barrel to catch and prevent excess glue from going into it. A ultra light layer of superglue on the window edges and let that sit for 5 min to harden, then do it again and immediately installed the r-hop. Make sure you know the orientation first. I used a 8mm wide rubber band and a book to apply pressure for 2 hours. Cleaned up the excess glue on the outside. After reinstating and using the Elvish Tac S-nub, I’m now landing .32g bb on target at 1.52j out of the barrel 220 feet away. Before I could just barely get to 200 feet.
E Wolf
Reviewed in the United States on April 3, 2023
Super simple to install. Fits exactly in the opening on the barrel.
budgetmaster
Reviewed in the United States on September 16, 2021
i did not glue mine in i used a thin wrap of thread tape. it works for me stays consistent to my red dot even after siting around a few months. results may vary... note it was not a major improvement over the krytac hop and bucking with .25 or .28 bbs... if i decide to use .30 or heavier this should shine superior...
Mostafa fawaz
Reviewed in the United States on September 10, 2021
Piece is made well and fits perfectly. Comes with good instructions. That doesn’t mean it’s easy. I glued mine down and my shots were curving to the right. I ordered a few more, if I can’t glue it down right I’ll just be sticking to maple leaf buckings and calling it a day.
Nikko
Reviewed in the United States on July 24, 2021
I purchased this r-hop for my Prometheus Krytac 6.03mm barrel. When I first glued the R-Hop on I was not setting it perfectly even on each edge of the hop window. After taking it off and resetting(and actually following the instructions closer) I was able to get it on much better than the first time. After letting it dry I could see it was not as perfect as I thought and decided to try it out anyway since it seemed to atleast be sealed well. Of course it did not fire as well as I hoped due to that imperfection. I contacted Elvish Tac just asking for some assistance in maybe providing an extra tip to make it fool-proof to install. ElvishTac responded promptly suggesting I try using some 6mm tubing or making something similar out of paper rolled up which is just enough to simulate the size of a bb in the barrel while also providing a perfect seating for the R-Hop. But not only did they provide that gem to send me on my way, I was also notified they were sending me an extra R-Hop free of charge. I received it and installed it immediately using the tips provided as well as using the additional online instructions for installation. ITS PERFECT. I can’t feel any edge of either the R-Hop or the window this time. After putting it all back and putting the S-Nub in the hopper to test it out and allowing for the R-Hop to fully set after a few hundred rounds this thing is a laser. My friends all want me to install it for them now. From the product all the way down to the instructions and customer service. THANK YOU ELVISH TAC! Definitely will be coming back for all my R-Hop needs in the future!
Sean Butler
Reviewed in the United States on January 22, 2021
Put this on my Prometheus 6.03 barrel with the larger “krytac” window, broke it in with a few hundred shots and it was good but not great like I was hoping for. I noticed the top wasn’t perfectly flush with the barrel possibly from excess glue. I sanded it flat and bam. It was shooting laser straight. Super impressed. Works better than any of the r hops i cut myself.
Kate
Reviewed in the United States on January 13, 2021
Wrong size, wrong angles, waste of time and money. Tried to contact customer service with no results. Don’t waste a second of your time or a penny of your money!
Recommended Products
$59.79
$ 28 .99 $28.99
$82.80
$ 38 .99 $38.99