Shopping Cart

Your cart is empty.

Your cart is empty.

SoloGood 5.8Ghz 2W VTX FPV Transmitter Over 20Km Range TS582000 5.8G 2000MW 8CH Video Transmitter with 5dbi SMA Antenna for FPV Racing Drone Quadcopter

Free shipping on orders over $29.99

$31.99

$ 13 .99 $13.99

In Stock
  • Product Name:new SoloGood 5.8Ghz 2W VTX FPV Transmitter 2000MW High Power born for fpv racing drone Quadcopter.
  • Newly upgraded power supply solution, using synchronous rectifier dcdc solution, no more skew, image quality has been greatly improved.
  • Light weight, double-sided heat sink, increase the power protection circuit to reduce the instantaneous easy burn phenomenon.
  • Increase the column fixed SMA interface, more resistant to bombing.
  • Newly upgraded to silicone wire, the wire is soft, not easy to break, can pass a large current.



Product Description

1
1

  • Transmission Characteristics:
  • Output Power:2000mW
  • Operating Voltage:8V-25V(2S-6S)
  • Operating Current:800mA(12V testing)
  • Channel :24CH Video
  • Format: NTSC/PAL
  • Output Voltage:5V/Input Voltage (Jumper cap selection)
  • Antenna Interface: SMA (External thread internal pin)
  • Weight:30g
  • Output Voltage:
  • Two output voltages, It can supply power to 5V and wide voltage cameras, Select the output voltage through a three-point jumper pad, and check the wiring scheme drawing for operation details.
  • 1.The jumper pad is short circuited to the two points on the right, and the output is 5V at this time.
  • 2.The jumper pad is short circuited to the left two points, and the input voltage of the power supply is output at this time.
1

Three schemes of actual wiring diagram:

1

  • (The picture above shows )Wiring scheme 1: It is suitable for micro camera with voltage of 3.3-5v and current less than 100mA. If there is no condition to verify that the camera meets the above voltage and current conditions, this wiring method is prohibited, otherwise there is a great risk of damaging the transmitter.
2

  • (The picture above shows )Wiring scheme 2: It is suitable for 5-25v wide voltage camera, and this scheme is universal.
3

  • (The picture above shows )Wiring scheme 3: It is suitable for the camera of scheme 2 which cannot be used when the voltage is low and scheme 1 cannot be used when the current is high, for example, a moving camera. This wiring scheme is universal and basically applicable to all cameras. The disadvantage is that the wiring is a little more complicated.

Tjam
Reviewed in the United States on September 6, 2023
junk
Tommy Oliver
Reviewed in the United States on August 12, 2023
I will be using this later this month for a project I'm working on. Currently, the product powers up, and lights and menu respond as explained on the Amazon instructions read. Both power and channel. However, the button will lock after the device runs for a bit and will only allow adjustment for a few min right after boot up. The device also holds the settings and will boot back to the last config. Seems like a great device and smart design. will update more later. No documents with device only the instructions on this page that are simple and clear to me. Did come with a few cables for different configurations.
Ken Bessler
Reviewed in the United States on June 30, 2023
The only problem is the fan bearings squeal a bit. Pretty common with these small chinese fans these days, kind of hit and miss on the quality, I got a defective one but I plan to upgrade the fan vs returning it for a refund. The rest of the unit seems very good. If you build drones you should understand the fan is a wear item. It's an easy swap.73
CBiggs Opinion
Reviewed in the United States on May 6, 2023
Received unit without any documentation. Not even a web address to get connection diagram. No idea how to change channels. Very poor.
peter20201
Reviewed in the United States on March 3, 2023
Workings good.
J No
Reviewed in the United States on February 19, 2023
Poor instructions, power and frequency button did nothing.
Bones83
Reviewed in the United States on February 12, 2023
I got this to add a camera to my rc car for FPV. The transmitter would not turn on. I tried 2 different cables that were provided and nothing. I changed my power source from using the receiver, to plugging into directly into a 7.4v battery, to a 14.8v battery. The transmitter never powered on and nor did the fan. I'm also not a fan that the dip switches to change some settings are under the heat sinks which are covered by what looks like warranty stickers over the screws. This is going back and Im trying something else that is less fishy in my opinion.
Judge
Reviewed in the United States on January 29, 2023
I am the person watching people fly 15 to 20 miles+ on 5.8ghz and just shake my head. I cannot figure how they do it, but I seem to be improving constantly. With my limited experience 3 years or so flying FPV, I'm always trying to go further, including 1.3 and 2.4ghz vtx's. For me 5.8 is easier, so I use it a lot, and I burn the them up a lot. Even with the antenna connected, they are getting too hot. I'm pleased to say this one with a fan has been a savior for me, I now put fans on most of mine. I have no way to test the output, but I have no reason to believe its less than the stated output of 2w. When I power it up at home, our internet gets overpowered and kicks off. I purchased another after my + experience
Recommended Products