Ok, so I started with 3d Materials a few years ago, after the sample resin that came with my Creality printer ran out. Over the past year, along with this 4k, I have used their 8k resin as well. I have also used resins (water washable and not) from three other manufacturers.Hands down 3d Materials is the better resin. Their Superfast 4k & 8k are extremely low odor, to the point that if I am just running the powered carbon filter in my Saturn 2, it is almost impossible to notice.When I used any of the three other mainstream brands, I ended up having to move my printer to a space in the garage.With odor out of the way, lets talk about "Superfast" and what actual speeds you can print at. With mainstream resins, you are laying your first layers down at 20 seconds a layer and your model layers in the 2.5 second range. With 3d Materials, I am constantly doing my initial layers at 2.8ish seconds and my model layers take less the 0.8 seconds. Yes you did read that correctly, model curing layers at less than a second. Depending on your machine, down as low as half a second.What about the quality? You do not sacrifice any quality for this speed. Models look great and print in a fraction of the time.

I've been fighting with Matterhackers Build Resin for 3 miserable months - adhesion issues, cure issues, now the parts sweat catalyst, a nightmare. I haven't had a success in that time. 3DMaterials was recommended to me for a resin that "just works".This resin worked instantly and near perfectly. I had to adjust my settings slightly and now BAM, no problems on a Mono X. Beautiful prints. I print larger models with bold details so I can't speak to small, fiddly details. I ran a resin test/calibration print a couple times and the small features looked good to me so that's my best input on detail-work.Resin is low odor, is printing well in our quite cold house. Surface feel after curing isn't as "silky" as some resins I've used but this isn't a detractor, merely an observation. Surface finish is a little matte.Customer support has also been truly excellent (in stark contrast to my experience w/ MH). Due to a logistics issue with amazon, I was sent an expired bottle of the wrong resin. It was handled overnight and I was sent a replacement. Support was professional, kind, and quick.

Gutes Produkt! Geringer Geruch und ein Top Preis/Leistungs-Verhältniss!Hab bis jetzt nur dieses Resin gekauft und würde er wieder kaufen. Super Haftung an Druckbett und eine Spitzen Druckqualität! Kundenservice ist sehr schnell wenn mal Fragen oder Bedenken hat!

Ich weiss nicht warum einige hier über mangehafte Haftung klagen aber das kann ich nicht bestätigen!Ich habe einen Wanhao D11 und habe die Druckbelichtungszeit auf 2 Sekunden gesenkt und es haftetbestens! Die Druckpräzision werde ich in den nächsten Tagen mit ein paar Bildern nachliefern.Ich bin mehr als begeistert und kann es nur empfehlen!

Ive tried 3 different brand resins so far. Ive had nothing but good results with this brand on my Mono X . I followed the recommended settings included with the resin.,which also allows the printer to be set at 50% UV power..so also allows my printer to last longer ,and at same time print faster.I havent noticed any effect on the details. I usually print 1/4 scale figures,so not sure about minis.Its suppose to be water washable ,but have found that water doesnt seem to remove ALL the uncured resin. I still dip the parts in alcohol ,then wash in tap water ,which worked much better than just the water.the only downside I really saw, and was mentioned is ,this resin is more brittle than the Elegoo standard grey that I was using. when test fitting some parts ,after apply pressure to a tight fit ,one edge snapped off...with Elegoo ,that wouldnt have happened ,as it does have some flexibility to it.Also ,with my support removal ,I run the part under hot water to make them come off cleaner...my medium supports come off easy without pitting , but the heavy supports I find harder to get them to break free without a big pit (Elegoo came off easy under hot water)

I wanted to try this out for 2 reasons: it's cheaper than most other water washable resins, and it says it's fast. Figured if it didn't work, it was at least trying in case it did. I have tried several water washable resins so far, and my favorite has been the NOVA3D water washable white. Used quite a bit of it and didn't have any major failures with it, and it printed really well. What this means is that I have a resin that is currently my go to when I don't want to test out new ones that works really well, and have a really good product to compare to.What are my thoughts on this Super Fast? I really like it! I cranked the settings all the way down on my Anycubic Photon Mono 2k. .6s layer cure, 5s base cure, .2 off time, and slower lift speed (2) with a higher lift (10mm), and faster lower speed (4). This has cut my print time in half from the NOVA3D (and almost 1/3 of the time for the Elegoo that I tried and did NOT like). After two prints with it, the details are on par with the NOVA, and am working on the third print right now. In the pictures, I am printing the Gorjira model from the Lord of the Print Patreon, and the white piece is the NOVA3D. The gray pieces are the 3DMaterials fast print. Other than color, I can't really see any difference in the quality, and it DOES print fast. The first arm took about 2 hours to print, and the tail and other arm took 6 (which would have taken around 12 with the NOVA).If I start having massive failures with this, which I am not currently anticipating, I will come back and adjust my review. So far, though, I am exceptionally impressed with it and might have found my new favorite resin!5/22/21 - An update to my review - So, I had a few failures. Couldn't figure out what the problem was until the LCD completely died. Replaced that, and I'm now successfully printing again! Completed the Lord of the Print Gojira print, and have now had around 9 successful prints since the LCD failed.If you find you're having issues with your prints being too brittle after you are done, make sure you check your cure time. I have dropped pieces on the floor and only lost the thinnest of bits, for instance the tip of a feather on one piece of a model, and a whisker on another piece. If you have a more powerful printer, like the Mono X, you have to make sure you dial down the UV intensity so that you don't cause problems. I have the Mono 2k, and I have my settings at 6s for the base, and .6s for the normal layers (50nm thickness), and I cure the smaller parts for around 3 minutes in the cure station, and around 7 minutes for larger pieces. If you go above those any, it will become brittle and you will lose detail from shrinkage.Final update - 6/10/21 - Had a few more failures, but turns out they weren't the resin's fault. One was the placement of the piece in relation to the holes that were hollowed out, and one was due to the failure of the adhesive for the magnetic build plate that I had installed. I'm still thoroughly happy with the quality of the prints, and continue to make outstanding stuff with it. Just about needing my fourth bottle of it!

ottima resina lavabile con acqua, a buon prezzo

I am really surprised by the quality of this resin.It delivers great printing results, great detail, good stability.if i had to mention one minor thing, prints need to be cleaned really well before curing to avoid grey *blooming* on the models.but other than this, great product for halt the price!

Genial. Por ahora no he tenido ningún problema con ella. Se lava con facilidad al agua (recomiendo un enjuage final con agua caliente). Cura muy bien al sol (todavía no he podido probarla con la máquina de curado, pero será igual o mejor).Incluye un manual con tiempos de exposición y potencias, incluidas las monocromaticas como la photon mono x. Valores que al menos en mi caso funcionan estupendamente.Muy contento con ella. Volveré a prbar pero en otro color.Por ahora estoy mas contento que con la elegoo al agua que era la que usaba antes (que también es buena, pero esta me ha gustado más).