Your cart is empty.
Your cart is empty.A top flow designed CPU cooler equipped with an optimized 120 mm high static pressure fan and a newly designed heat sink. Intel and AMD socket. •P/N: CL-P073-AL12BL-A •COMPATIBILITY: Intel LGA 1200/1156/1155/1151/1150, AMD •AM4/AM3+/AM3/AM2+/AM2/FM2/FM1 •DIMENSIONS: 137.7 x 123.6 x 114.1 mm ( L x W x H) •HEATSINK MATERIAL: Aluminum Fins Copper Heatpipes •HEATPIPE: Φ6mm x 4 pcs •FAN DIMENSION: 120 x 120 x 25 mm ( L x W x H) •FAN QUANTITY: 1pcs •FAN SPEED: PWM 500 ~ 2000 RPM •RATED VOLTAGE: 12V •START VOLTAGE: 9.0 V •RATED CURRENT: 0.48 A •POWER INPUT: 5.76 W •AIR FLOW: 58.35 CFM •AIR PRESSURE: 2.41 mm-H2O •ACOUSTICAL NOISE: 23.6 dBA •LIFE TIME/FAN LIFE TIME: 40,000 hours •PIN CONNECT: 2510 - 4Pin •COOLING POWER: 140 W
Shawn
Reviewed in the United States on May 2, 2025
one of the best
JB
Reviewed in the United States on March 19, 2025
I normally go with a liquid cooling system on my builds, but this one was for my wife who uses her computer very lightly, so I thought that this would be adequate. My only concern was if it would make a racket. Well it is extremely quiet, and it has plenty of cooling power for her i3 processor. I suspect that it might work in a more challenging setup, and I may go this route in the next build for myself.
Jesus Sanchez
Reviewed in Mexico on July 16, 2024
Si lo encuentras por menos de $1000, es una excelente opción para tener tu cpu con buenas temperaturas.Fácil de instalar materiales de buena calidad sencillo pero muy práctico.Solo una cosita que hay que tener en cuenta, que si tienes unas memorias ram un poco altas pueden que choquen un poco , lo recomendable unas de perfil bajo
Glitchvid
Reviewed in the United States on December 28, 2024
This does a great job as a downdraft cooler for my AM4 board, keeps the CPU cool and also provides lots of airflow for the anemic VRMs.Installation was miserable, very obviously where the cost cutting went, if I did it again I'd go for a Noctua solution just for their significantly better mounting design.
CaseyDalPal
Reviewed in the United States on November 18, 2024
it was not the easiest to install, but it had PICTURE instructions, all the pieces were clearly labeled. it works with both AMD and Intel processors. it took me about 30 minutes to install. It came with good CPU paste. I really liked the way the fan was attached. i9 12900K runs at 31c under light loads and never above 59c even when I have it working real hard. It is a good choice for air cool.
Goldilockz
Reviewed in the United States on December 31, 2023
Replaced a stock AMD cooler on my old AM3 (AMD Phenom II x6 1090T) build, with no problems on install or setup. Looks great and I actually prefer the look of the top flow more than the standard tower. The fan is extremely quiet, and ramps up and down as it should. I dont have any overheating while running 3DMark (Firestrike),Heaven Benchmark 4 or any game, so far. Didn't have any problems during install, very easy and simple instructions if you don't jump ahead of the step with the standoffs/spacers. The only question I had with the install was that it seemed more "loose" than I wanted. Once my thermal paste cured a bit its solid now, so maybe it is just me being picky. Great install though! The height of the fins is high enough to have space for my DDR3 RAM with coolers underneath. Installed on a Asus Crosshair IV mobo with 125W TDP processor (overclocked pulling 141.6W TDP), Patriot Viper RAM, Asus TUF GTX 1660 Super, Thermaltake 600W PSU.If anything negative happens in the future, I will try to update.
Jerry E Dean
Reviewed in the United States on October 22, 2023
I am so much against these company’s wanting you to dismantle the computer just to put in there fan. They all mount to the motherboard and you should be able to use what is already there. All the extra hardware is An overkill. Make them to fit Intel or AMD without having to remove the existing hardware. I am not A fan of removing the motherboard just to install there special brace. If it is A liquid cooling setup I understand but make there are coolers A more basic setup without alll the extra parts, I had to dremel the screw holes on the metal part just to get the screws in to install it after removing the stock plate from the motherboard. The cooler works good but the install was way too difficult. The water cooler is easier to put in than this
Filiberto Yescas Santos
Reviewed in Mexico on August 9, 2022
trabaja bien, auque con el procesador en mod turbo hace ruido, pero es normal por las rpm que alcanza, y para eso esta diseñado.
Araceli
Reviewed in Mexico on March 30, 2022
Estaba buscando un producto de estás características, un tanto diferente a los disipadores de torre pero similares al tener el ventilador dirigido hacia la placa ayuda al enfriamiento no solo del disipador, también de la ram y la mobo, es facil se instalar y puedes colocarlo en diferentes posiciones lo cual te ayuda a un acomodo estético, me gusta la posibilidad de cambiar el fan por otros lo cual te da más opciones de personalizar tu pc yo cambié el fan que trae ya que no cuenta con iluminación por un Cooler Master MasterFan SF120M ARGB Ventilador premium y quedó genial, ten en cuenta que aunque tiene espacio suficiente si tienes ram de perfil alto como las delta de team group va a pegar con las memorias pero al poder reacomodarlo en diferentes posiciones no hay problema, lo puse en un rayzen 7 y anda en 35 a 45 hasta los 55 grados de temperatura, nada fuera de lo común
Alejandro
Reviewed in Mexico on December 10, 2022
Lo instale junto con un i5-11400 y obtiene buenas temperaturas, su instalación fue sencilla y no estorba con las memorias ya que tiene una altura suficiente.
Adrian
Reviewed in the United States on October 24, 2022
I have it on a ryzen 1800x, 95w. It is one of the best mounting systems that I've seen, and I've seen quite a few (coolermaster, arctic..etc). Massive heatsink, but not excessively so, still light and manageable. No issues with memory sticks, it sits much higher. The fan is very quiet and works great, but you can replace it with any other 120mm fan, which is of course a big advantage. I would definitely purchase again if I needed another one.
KG
Reviewed in Canada on November 23, 2021
I could tell from the tape on the box that this probably wasn't a new item, and when I opened it there was already thermal paste on the heat sink and no thermal paste in the included syringe.100% disappointed.
Wayne T. Peters
Reviewed in the United States on November 12, 2021
Seems to be cooling a 12700K quite well I have not gamed with it yet. But a very quiet not huge cooler. Nice work Thermaltake. The enclosed instructions did not show the screw placements for LGA1700 but I DL the instructions and it showed you use "B". Nice heatsink
Recommended Products
