Shopping Cart

Your cart is empty.

Your cart is empty.

Time Relay, DC 5V-36V Trigger Cycle Delay Timer Switch Turn On/Off Relay Module with LED Display for Smart Home, Tachograph, GPS, PLC Control, Industrial Control, Electronic

Free shipping on orders over $29.99

$7.25

$ 2 .99 $2.99

In Stock

About this item

  • ✪✪✪✪✪ [Fast] To log a rapid circuit of high frequency on and off, an unlimited number of time of switching.
  • ✪✪✪✪✪ [No Noise] No noise was made during power on / off, neither spark, nor electromagnetic interference.
  • ✪✪✪✪✪ [More Durable] In comparison with the normal electromagnetic relay methods, it's a longer service life.
  • ✪✪✪✪✪ [Dual MOS] Dual MOS in parallel active output, internal lower resistance, higher current, strong power; At room temperature, the working current is up to 15A, power up to 400W, those can for most equipment.
  • ✪✪✪✪✪ [Applicable] Voltage input widens from 5V to 36V, normally used to control DC motors, lights, LED strips, micro-pumps, solenoid valves, etc., very convenient.


Specifications: Voltage: DC 5V~36V.
Trigger Signal Source: High voltage level trigger (3.0V~24V), signal ground and system ground are not on common ground to improve the system's anti-jamming capability (you can also connect them on common ground).
Output Capacity: DC 5V~36V, at room temperature, continuous current is 15A, power 400W. With enhanced heat dissipation, the current can be up to 30A.
Quiescent Current: 20mA
Operating Current: 50mA
Working Temperature: -40~85
Clocking (Time Delay) Range: 0.1seconds to 999minutes
Size: 60*34*12mm / 2.36*1.33*0.47"

Instruction:
Operating Mode:
P1: trigger signal, the relay is on "OP" time, and then disconnect; in the "OP" time, as follows:
P1.1: signal is triggered again, invalid
P1.2: signal is triggered again, the clocking is reset
P1.3: Signal is trigger again reset, relay off, and stop the clocking;
P-2: trigger signal, the relay off "CL" of time, the relay on "OP" time, and then disconnect relay after clocking;

Note:
1. The module is an active output, the output voltage equal to the input voltage.
2.'DC + 'and' load + ' are internally shorted(connected), but' DC- 'and' load - ' cannot be shorted, otherwise the load cannot be controlled on and off, which is equivalent to load being powered on always.

Package Includes:
1 x Timer Switch Module


Customer
Reviewed in the United States on May 10, 2023
I've supplied 12v to the board and the display doesn't stay on for more than 10 seconds, and it came with zero instructions or documentation.
Corcodus
Reviewed in the United States on March 27, 2023
There is something wrong with these relays.I bought one and arrived dead, so I thought that was just a dud.I returned it for a replacement and it worked for few minutes, before blowing a whiff of smoke.All I did was to connect it to a 12V DC regulated source, program it for P 3.2 and let it work while I checked the output.I will not replace it with the same, that's for sure!
Enoch Del Rio Amezquita
Reviewed in Mexico on December 16, 2023
Me fue de mucha utilidad y buen producto, solo le falta traer una guía de programación o un enlace para su uso, lo bueno que hay tutoriales en línea y fue fácil de programar
George robert
Reviewed in the United States on January 16, 2023
Can't beat the price . works great !!
Glen Blake
Reviewed in the United States on February 6, 2022
This was very hard to program. I watched a very good video on how to program unit. After I had it programmed the unit would not shut off the light. I have read that others have had faulty units.
babato
Reviewed in Mexico on October 6, 2022
Excelente, cumple a la perfección su función.al principio me costos trabajo entender como conectarlo, ya que no tengo conocimientos de electrónica, sin embargo, ya después se me hizo muy fácil.
Óscar D.
Reviewed in Mexico on October 20, 2022
Lo único que le hace falta un manual para programarlo, por lo demás excelente circuito.
RT
Reviewed in the United States on September 22, 2021
It states that it is a 5-36V output timer, but on the back of the board it clearly says 5-30V and when I apply 33V to the power side, the screen flickers and the board does not function.
gery
Reviewed in the United States on August 13, 2019
Very nice unit, answer questions quickly