Your cart is empty.
Your cart is empty.Product Description
Product Description
Designed to connect and disconnect an DC12V 20A electrical circuit at will,SPST:ON-OFF 2 pole；LED Color：Blue；Type:2 Pins (3 Pins with LED)Color：Blue
When the switch is on, The LED lights will come on；Hole diameter：20mm/0.8"；And it comes with a keyhole slot to prevent unwanted rotation
This truck rocker switch control uses copper-plated silver contacts, has good electrical conductivity, and uses high-quality materials and flame-retardant casing for high safety
3 Gang Round Dot Lighted Rocker Switch Toggle Metal Panel
Suitable for car,truck,boat,atv,motorbike etc.Can also use these on water dispenser, running machine,electromobile and other household appliances modification.
Kimberly Dillard
Reviewed in the United States on May 4, 2025
Husband used this in an FFA Project to make the trailer lights work for a competition.Worked well and arrived in time.
patrick
Reviewed in Canada on March 9, 2025
So far so good, not sure how long it will last, but i didnt have many options for switches so Inused this setup. Fits nicely
Sebastien lefebvre
Reviewed in Canada on March 29, 2025
Très bien
Austin Barrett
Reviewed in the United States on January 23, 2025
Works good. Easy to wire up. Just have to run one set of positive and negative from the battery to it and you can run something off all 3 switches. I have a light bar and bed lights hooked up to it and it works great. I wanted the LEDs so I could see the buttons at night but the blue LEDs on the switches are a little bit too bright when you’re driving. But I do have it mounted on my dash. I could probably put something over then to dim them a bit. But otherwise it’s good.
Dave B
Reviewed in Canada on August 30, 2024
One switch conked out and had to be replaced
Marc
Reviewed in Canada on March 31, 2024
Après installation ça semblait bien mais après seulement un lavage 2 sur 3 boutons ne fonctionne plus , cochonnerie
The Boatmaster
Reviewed in the United States on December 18, 2024
I installed these in my teardrop trailer for front and rear interior lights and exterior light. They look and work good for the pupose. A+
reginald braxton
Reviewed in the United States on November 15, 2024
Looks to be of good quality. Haven't installed it yet.
Ednara
Reviewed in the United States on October 12, 2024
I recently replaced an old rocker toggle switch in my RV with this 3 hanger version, and it worked perfectly! Installation was easy, and it’s a great fit. The functionality is smooth, and it looks much better than my old switch. Very happy with the upgrade—would definitely recommend it to anyone needing a reliable replacement!
DonInNC
Reviewed in the United States on August 31, 2023
Installed in my camper van build. Seems good quality and I wanted indicator lights for I would be able to cut off power to my water pump, lights, and power ports.
John
Reviewed in Canada on October 13, 2023
Works great as a single pole switch for my Dishy Dualie for Starlink 12v conversion!
John Smith
Reviewed in the United States on October 10, 2023
NO INSTRUCTIONS At All - You are on your own. I do have to give credit to someone who purchased before me who was instrumental in my success in installing.The back of each plug has three male spades that are for connecting the ground (black) wires and positive (red) that come with the unit. Here is how I connected mine:One Gold Spade - Connect your included Black wiring for your Ground (from your battery or grounding source).Middle Spade - This is your Red wires - your Positive In (from your power source).Silver Spade (last one left) feeds the power to whatever you are powering.So to get power from say my 12v battery to the rocker panel, I ran one positive wire and one ground wire from the battery. I purchased a grounding block to connect the main ground from the battery to the block, then use this for all the grounds for my electronics to this block.Then, I ran the negative (black) wire from the switch and then connected it to the grounding block - this takes care of all your grounds that are or will be used with the rocker panel.Then I connected the One Positive wire to the (red) power wire from the Rocker panel and this provides power for anything that is connected to the switch.So at this point, you now have your power to the Rocker Panel and the Ground as well.So, if you have like say you want to add a LED light that needs 12V power to the Rocker Panel, you add a female spade to your positive and connect it to whatever switch you want on the Rocker Panel and you connect your ground to the ground block and you are done.Hope this Helps - Give me a Thumbs Up!
Bob
Reviewed in the United States on August 12, 2022
Such cheap metal on the connectors they would not even stay plugged in. By the way I had to put it together myself. Wish I could just buy the panel for like 99 cents and do the rest myself but for $10.00 I can't complain too much.
Recommended Products