Shopping Cart

Your cart is empty.

Your cart is empty.

Water Leak Detector with Sensor Alarm, Power Insufficient Detection, Auto Shut-Off, Water-Saving, Home Assistant, Automation Improvement for Bathroom, Laundry, Basement, Kitchen

Free shipping on orders over $29.99

$33.99

$ 14 .99 $14.99

In Stock

About this item

  • 【Auto Shut-off】: When water seepage is detected, the switch will automatically turn off to ensure safety and protect against water leaks, addressing any potential issues caused by water exposure.
  • 【Versatile Fit for Your Home Plumbing Needs】: Comes with both 3/8" and 1/4" od quick fittings – perfect for different pipe sizes. Includes a handy installation guide for easy setup!
  • 【Power Detection】: The water detector will automatically shut off to prevent over-discharging or damage when the power is insufficient.
  • 【Reduce Impurities and Scale】: The circuit board has been modified to disconnect power for 0.5 seconds each day, helping to reduce the accumulation of impurities and limescale on the solenoid valve spring.
  • 【High Applicability】: Suitable for drinking water filtration, water softeners, sink and laundry helping to maintain optimal performance and reliability over time.



Product Description

How the Leak Detector Works

installation 1

Step 1

Just install the valve in front of inlet tube and put it with detecting metal down on the floor near water systems.

installation 2

Step 2

As detecting the leak, it will initiate an Audible alarm and indicator will light up.

notice

Step 3

It will automatically cut the water supply when a leak is detected.

IDENTER Leaky Savior Auto Water Leak Protector Shut-Off Water Valve shuts off flow to the water system as a leak should occur. It can avoid water damage from a leak effectively!

as-414 top

Package includes:

  • 1 x Auto water shut-off valve
  • 1 x 9V Battery
  • 2 x Quick fitting 1/4"OD-1/2"BSP
  • 2 x Quick fitting 3/8"OD-1/2"BSP
  • 1 x User Manual

Technical Specifications:

  • Operating Voltage Range: 9 DC Volts (Alkaline battery only)
  • Operating Current: typical 1 mA, maximum 15 mA.
  • Cable Length (for solenoid valve cord): 1.5 M
  • Connection: 1/2 inch BSP male
  • Environment temperature: -20 ~ 80℃ / -4 ~ 176°F
  • Maximum Pressure: 6 Bar
detect

Powered by 9V alkaline batteries, the auto water shut-off valve can also shut down when reaching a low battery state.

As long as you install this valve in front of inlet tube and put it with detecting metal down on the floor near water systems, you will not worry about water leaks anymore!

Installation Steps:

Step 1 - Install the Correct Fitting: Choose the appropriate quick fitting based on your water line size: either the 1/4" OD to 1/2" BSP or the 3/8" OD to 1/2" BSP. Attach the fitting securely to the leak detector to ensure a proper seal.

Step 2 - Insert the Battery: Open the battery compartment and insert the 9V alkaline battery included in the package. Make sure the battery is properly installed to power the device.

Step 3 - Shut Off the Main Water Supply: Turn off the main water supply to your house to avoid any accidental leaks during the installation process.

Step 4 - Drain the Water from Your Faucets: Open all nearby faucets to allow any remaining water in the pipes to drain completely. This will make it easier to cut the water line without water spilling out.

Step 5 - Cut the Water Line: Carefully cut the water pipe where you plan to install the leak detector. Ensure the pipe is dry and free of water before proceeding.

Step 6 - Connect the Pipes to the Leak Detector: The elbow valve on the leak detector has an engraved arrow to guide the installation. Connect the pipes according to the arrow’s direction: the tip of the arrow indicates the water outlet, while the tail shows the inlet. Be sure to follow this orientation to ensure proper water flow and functionality.

Step 7 - Position the Leak Detection Plates: Place the metal leak detection plates on the floor near a potential leak source, such as near a water filter or under a sink. Make sure the plates are flat on the ground to accurately detect any water leakage.

Step 8 - Activate the Leak Detector: Press and hold the activation button for four seconds to power on the device. The leak detector will now be actively monitoring for any water leaks.


Dave
Reviewed in the United States on January 5, 2025
I grabbed this Water Leak Detector because, let’s be real, water leaks are sneaky little nightmares. This handy gadget has been a solid addition to keeping my house safe from unexpected messes.🚰 What’s Great:Reliable Leak Detection: The sensor is super sensitive. It caught a tiny leak under my sink before it could turn into a full-blown disaster.Loud Alarm: If water hits the sensor, the alarm is loud enough to hear from another room, which is a lifesaver for peace of mind.Auto Shut-Off Feature: This is my favorite part! If it detects water, it cuts off the flow to save water and minimize damage. Genius.Battery Monitoring: It lets you know when the battery’s low, so you’re never caught off guard.🤷‍♂️ A Few Things to Consider:Setup Takes a Minute: Figuring out the best spot for the sensor and connecting it to the auto shut-off valve took a little trial and error. Nothing crazy, but don’t expect plug-and-play.Alarm Volume Isn’t Adjustable: It’s loud, which is great for emergencies, but you might wish for a volume option if you’re in a small space.🛠️ Compared to Others:This one stands out for the auto shut-off and battery monitoring. A lot of basic leak detectors just beep and leave you to figure out the rest, so this feels like an upgrade for anyone serious about water damage prevention.If you’ve got areas prone to leaks—like the bathroom, laundry room, or kitchen—this little gadget is worth it. It’s a small investment for big peace of mind. 🌊🔔
Recommended Products