Your cart is empty.
Your cart is empty.Product Description
Xadnitu 1/2" EMT to EMT 90 Degree Connector
For your conduit management.
Reliable Quality
Having the structure of die cast, UL and CSA certifications.
Glossy Surface
EMT coupling has a smooth surface, allowing safer and more comfortable use, while avoiding scratches on the pipes.
Including three components
Assembly Parts
- a right angle connector part
- a removable cover
- four combo screws
Suitable for both indoors and outdoors use
Wide applications
Factory, garden, home, construction and other applications need to connect pipes;
Can accommodate tubes or pipes with a maximum diameter of 1/2 inch.
- Corrosion Prevention
- Wear Resistance
- Rust Resistant
- Die-casting Constructure
- UL Certification
- CSA Listed
sami
Reviewed in the United States on May 10, 2025
Good
The Nelsons
Reviewed in the United States on March 17, 2025
These are great EMT 90 degree screw connectors for electrical conduit work. I couldn't find any real differences between these and a pack I picked up from the box store. Pipe hole size was correct, and the EMT inserted with the right amount of play, and I had no thread issues tightening down the connector to the pipe. Great value!
Cycletime 71
Reviewed in the United States on March 17, 2025
I used these 90 degree elbow connectors for installing a motion sensor light on my brick house. Everything went together without issue.
S. Meyer
Reviewed in the United States on March 16, 2025
These work great for keeping inside conduit corners tight to the structure they are mounted to. I’m using them in a storage shed where I don’t want any chance of someone hanging items from exposed conduit. Because of the tight turn on these I only pulled wire through one fitting at a time. The removable cover made this easy.Smooth radius bends in conduit are preferred for pulling wire, and wires can be pulled through a total of 360 degrees at one time. Not so with these. But if bending conduit won’t work for your application then these are helpful.One note; these are made of zinc alloy and will break if under tension. Nothing unusual about that as most 1/2 inch conduit fittings are zinc.Steel fittings are available at electrical suppliers houses.
YKNOT
Reviewed in the United States on February 22, 2025
Fits 1/2 inch EMT just right. These make a clean, compact 90 degree turn while still allowing easy pull of wires with the pull access. I'm going to get more of these.
Allison
Reviewed in the United States on January 30, 2025
This conduit fitting is really great for small indoor spaces. Whereas a sweeping 90 degree made with a bender would take up space or may be in the way.My example is a shed aka art room where space is not to be wasted. For example using an LB fitting doesn't work in certain areas because the opening wouldn't be accessible. These Xadnitu Inside Corner Pulling Elbows are prefect for keeping the conduit close to the corners out of the way and are easy to use.These are made well with consistent quality. So glad I ran across these conduit fittings.
R. Moheban
Reviewed in the United States on January 23, 2025
I expect these metal conduit ells have no trouble meeting building codes. They appear to be the same quality as EMT connectors typically found at home improvement stores. The construction is all metal.The removable plates allow plenty of room for pulling wires straight. Sometimes wires simply won't pull when going around corners; these fittings eliminate the corner problem. They also eliminate having to make double bends in a piece of conduit. I've mangled more than one job by trying to bend a single piece in two directions. If I had these 90 degree fittings I could have made just a single bend and gotten a much more professional result.Inspecting all the 10 pieces I couldn't find any flaws. A couple of screws had fallen out but I found them in the bag. The manufacturer could ensure the set screws are screwed in further so they don't fall out in transit, but it's a small quibble.While ten of these costs currently around 22 dollars, as I don't know whether that price is typical or high, I will rate this product five stars as a good, suitable product with good quality control. As for the value buyers may want to comparison shop.
Customer
Reviewed in the United States on January 21, 2025
These are exactly as advertised and fit 1/2" EMT conduit nicely. And if you haven't used this type of elbow before, I highly recommend it because it makes it so much easier to pull the wires through, while not taking up as much space as a curved 90-degree elbow.
Recommended Products